66 Ferm
SPARE PARTS LIST FOS-500
REF NR DESCRIPTION FERM NR
001 PLASTIC PLATE 408700
002 BASE PLATE 408701
005 KNOB 408702
006 LEVER FOR FIXING RING 408703
007 NUT 408704
008 COLLET 1/4” 408705
009 COLLET 1/8” 408706
012 BEARING 408707
016 LOCKING PIN 408708
019 ROTOR 408709
020 BEARING (608 Z) 800608
021 RUBBER BEARING HOLDER 408710
025 STATOR 408711
028 CARBON BRUSH SET 408712
037 SWITCH 408713
044 KNOB FOR HANDLE 408714
045 HANDLE 408715
046 WRENCH 408716
OMNISAW
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE PICTURES AT PAGE 2
TECHNICAL SPECIFICATIONS
DESCRIPTION
Fig.A
1. Base plate and depth guide
2. Collet nut
3. Spindle lock button
4. Exhaust air vents
5. Removable auxiliary handle
6. On/off slide switch
7. Intake air vents
8. Power supply cable
9. Depth guide bracket
10. Depth guide locking knob
11. Locking knob of depth guide bracket
12. Bit
13. Protection guide cap (not shown)
PACKAGE CONTENTS
1 Omnisaw
1 1/4" collet
1 1/4" Window/Door Bit (ZBWD8) for Plaster cutting
1/4"
1 1/8" Guidepoint Bit (GP10) for Drywall cutting 1/8"
1 1/8" Outlet Bit (ZB10) for Plaster cutting 1/8"
2 1/8" Sabrecut Bit (ZBSC5) for Wood/Plastic cutting
1/8"
1 1/8" Tilecut Bit (RZ125) for Ceramic cutting 1/8"
1 Wrench
1 Protection guide cap
1 Carrying case
Check the machine, loose parts and accessories for
transport damage.
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
BEFORE USING THE OMNISAW
• Check the voltage of the motor and the motor over-
load (if any) correspond:
Do the voltage of the engine and the engine safe-
guard, if any, correspond to the mains voltage
(appliances for a mains voltage of 230 V).
Are the mains lead and the mains plug in a good condi-
tion: solid, without any loose ends or damage.
• Remove adjusting keys or wrenches before turning
the tool on.
• Always wear eye protection when using the tool.
• Maintain the tool with care.
• Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tools operation. If damaged, have the tool
serviced before using.
• Use only accessories that are recommended by the
manufacturer for your model.
• Compare the maximum number of revolutions allo-
wed of the accessories with the number of revolu-
tions of the machine.
• Make sure that the spring chuck diameter is the same
as the axle diameter of the accessory.
• The flutes of the bits (cutting edges and top) are very
sharp. Therefore, handle with caution.
USING THE MACHINE
• Use clamps or a vice to hold the work.
• Do not use the tool if the switch does not turn it
"ON" or "OFF".
• Always hold the tool with two hands while starting.
• Hold the tool by the insulated gripping surfaces when
performing an operation where the bit may contact
hidden wiring. If cutting into existing walls or other
blind areas is unavoidable, disconnect all fuses or cir-
cuit breakers to the worksite.
• Always keep the cord away from the moving parts of
the machine.
Voltage | 230 V~
Frequency | 50 Hz
Power input | 500 W
Speed, no load | 30000/min
Nett weight | 1.51 kg
Lpa (sound pressure) | 83.9 dB(A)
Lwa (sound power level) | 96.9 dB(A)
Vibration value | 4.6 m/s
2
