Bedienungsanleitung Ferm HDM1026S (Seite 5 von 116) (Alle Sprachen)

762286

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Replacement of power cords or plugs

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important

that it is correctly destroyed and replaced by



the following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

• blue neutral

• brown live

As the colours of the wires in the mains cable

of the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

• The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

• The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

Use of extension leads

Only ever use approved extension leads that are

suitable for the power rating of the machine. The

minimum core thickness is 1.5 mm2. Whenever

using a reel extension lead, always fully unroll the

lead.

Immediately switch off the machine when:

• Excessive sparking of the carbon brushes.

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

2. MACHINE INFORMATION

Intended use

This rotary hammer is intended for drilling holes

in masonry such as brick, concrete and similar

material. Furthermore, the machine can be used

as a demolition hammer in combination with the

SDS cold chisels provided. The machine is on no

account intended for other purposes.

Not suitable for construction site usage

Technical specifications HDM1026S HDM1027S

Mains voltage 230-240 V ~ 230-240 V ~

Mains frequency 50 Hz 50 Hz

Power input 600 W 950 W

No-load speed 0-1100 /min 0-960 /min

Impact rate 0-5800 /min 0-4550 /min

Max. Drill diameter

-Concrete

-Steel

-Wood

Ø 20 mm

Ø 13 mm

Ø 30 mm

Ø 26 mm

Ø 13 mm

Ø 30 mm

Weight 2.8kg 3.4kg

Sound pressure (LPA)91.18dB(A)

K=3 dB(A)

90.8dB(A)

K=3 dB(A)

Acoustic power (LWA)102.18dB(A)

K=3 dB(A)

101.8dB(A)

K=3 dB(A))

Vibration

hammer drilling concrete

ah,HD

13.719m/s2

K=1.5m/s2

12.133m/s2

K=1.5m/s2

Chiseling ah,Cheq

10.174m/s2

K=1.5m/s2

13.087m/s2

K=1.5m/s2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardized test given in

EN60745. It may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories,

may significantly increase the exposure level.

• The times when the tool is switched off or

when it is running but not actually doing the

job, may significantly reduce the exposure

level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm and organizing your work

patterns.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm HDM1026S Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info