764186
5
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
5
EN
Additional safety instructions
• Pleasecheckworkpiecesforanyobstructions
on the surface of the material, such as
protruding nails etc., to protect the trimmer
head.
• Waituntilthetrimmerhascometoacomplete
stop before removing any blocked or routed
material around the cutter. Use a long stick for
this and never your finger.
• Pleasekeepyourhandsawayfromtherouting
surface.
• Immediatelyswitchoffthetoolifitstarts
producing any unusual noise or starts vibrating
excessively.
• Pleasecheckthatallpartsaresecure,tools
are removed etc. before operation.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated,
therefore no earthwire is required.
• Immediatelythrowawayoldcablesorplugs
whentheyhavebeenreplacedbynewones.It
is dangerous to insert the plug of a loose cable
in the wall outlet.
• Onlyuseanapprovedextensioncablesuitable
for the power input of the machine. The
minimum conductor size is 1.5 mm2. When
using a cable reel always unwind the reel
completely.
Prior to mounting an accessory always
unplug the tool.
Wait until the machine has come to a
complete standstill and the cutter has
cooled down before replacing a cutter.
3. ASSEMBLY
Router Bit Selection
Depending on processing and application, router
bits are available in the most different designs and
qualities:
Router bits made of high speed steel (HSS) are
suitable for working with soft materials, e. g. soft
wood and plastic.
Carbide tipped router bits (HM) are particularly
suitable for hard and abrasive materials, e. g. hard
wood and aluminium.
Mounting and removing cutters
Fig. C
Only use cutters with a shaft diameter which
corresponds with the size of the collet. Only use
cutters which are suited for the maximum speed
of the machine. The cutter diameter should not
exceed the maximum diameter.
Never tighten the collet nut, if there is no router bit
in the collet; the collet may be damaged.
• Lockthespindle(7)byholdingitwiththesmall
spanner.
• Openthecolletnut(6)usingthebigspanner.
• Placethecuttershaftinthecollet.
• Tightenthecolletnutsothatthecutteris
locked properly.
• Openthecolletnut(6)whenyouwantto
replace a cutter.
Adjusting the parallel guide
Fig. D1
The parallel guide is a useful tool for precision
routing at a fixed distance from the edge of the
workpiece or another ridge. This tool can also be
used to trim circles.
• Placethedesiredcutterinthetool.
• Slidetheparallelguide(9)intotheaccessory
holder.
Mounting the template guide
Fig. D2
The template guide is a handy aid for cutting a
pattern when the template guide is mounted, you
can easily run it along a pre-cut template to cut
the material beneath in the same shape.
• Mountthetemplateguide(11)onthetrimmer
by removing the bottom plate and mounting
the template guide between the trimmer base
plate and the bottom plate.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferm PRM1020P wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info