Bedienungsanleitung Ferm TCM1012 (Seite 2 von 16) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

764185

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

TILE CUTTER

Thank you for buying this Ferm product.

By doing so you now have an excellent product,

delivered by one of Europeís leading suppliers.

All products delivered to you by Ferm are

manufactured according to the highest standards

of performance and safety. As part of our

philosophy we also provide an excellent customer

service, backed by our comprehensive Warranty.

We hope you will enjoy using this product for

many years to come.

Read the operating instructions

carefully before using this device.

Familiarize yourself with its functions

and basic operation. Service the device

as per the instructions to ensure that it

always functions properly. The

operating instructions and the

accompanying documentation must be

kept in the vicinity of the device.

Contents

1. Technical specifications

2. Safety instructions

3. Assembly

4. Use

5. Maintenance

1. Technical specifications

max. 10 mm

max. 400 mm

30-80 mm

0-45°

2. Special safety instructions

1. The tile cutting machine is fitted with a

replaceable circular blade. Therefore, keep

children away.

2. After use the machine must be stored in a

safe and dry place, away from children.

3. This machine has been designed for cutting

and breaking glazed tiles, and must not be

used for any other purpose.

4. When using the tile cutting machine make

sure to keep extension leads and such away

from the machine.

5. Always place the tile cutting machine on a

level and firm surface.

6. CAUTION! The edges of cut tiles are sharp.

3. Assembly

Assemble the tile cutting machine as shown in the

drawing.

Assembly of the tile cutting machine

Remove all the parts from the box and assemble

the tile cutting machine as follows:

1. Slide the black rubber feet (T) over the

corners of the tile cutter. Slide a washer onto

the bolt and push this into the rubber foot.

Now slide a washer and a nut over the bolt on

the back and fasten this properly. Repeat this

for the other three corners.

2. Mount the fastening blocks (N) with the 2

tubes (M) onto the bottom plate (V) using the

4 bolts (O) and washers (P).

3. Screw the lever (H) onto the tube fastening (I).

4. Finally, mount the sash angle (U) onto the

bottom plate (V) using the knob (S) and

washer.

Assembly of the hollow square chisel

1. Place the hollow square chisel above the hole

in the bottom plate (V).

2. Make sure that the clamping plate (E) comes

under the 2 tubes and fasten this using the

socket head wrench supplied. The socket

head wrench is situated in the black fastening

plate (C).

3. It is important that the drill (G) and the knife

(F) are adjusted in such a way that they just

touch the bottom plate (V). This adjustment

can be done using the two nuts at the top of

the hollow square chisel. Then fasten these

nuts against each other.

3. How to cut and break tiles

1. Use a soft-tipped (carpenter’s) pencil to mark

off the cutting line.

2. Place the tile against the stop, the glazed

side facing upward. The pencil mark must be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TCM1012 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info