58 Ferm
SPARE PARTS LIST FTB-13MV
REF NR DESCRIPTION FERM NR
27 MOTOR 311053
37 MAGNETIC SWITCH 311051
50 COVER FOR SPRING 311059
51 SPRING 311058
56 CHUCK GUARD 311055
58 V-BELT 800157
10 CHUCK 311054
- CHUCK KEY 311057
-CONDENSER 311056
- MACHINE VICE TDA 1008
Bench pillar drill with machine vice
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE PICTURES AT PAGE 2
TECHNICAL SPECIFICATIONS
PRODUCT INFORMATION
Fig.A
1. On/off switch
2. Drill depth gauge
3. Protection guard
4. Motor
5. Drill depth lever
6. Table adjustment
Check first whether or not the delivery has been dama-
ged by transport and/or whether all the parts are pre-
sent.
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Keep these instructions in a safe place!
Before using the machine the guidelines must be taken
into consideration. Every mechanical or electrical altera-
tion to the machine which does not meet the applicable
guidelines carries a considerable accident risk.
DURING USE THE FOLLOWING POINTS
MUST BE CONSIDERED:
• Do not remove any mechanical or electrical protec-
tive provisions.
• Check whether all the protective provisions are in
place and have been attached correctly.
• Wear safety goggles during drilling.
• If you have long hair, be sure to wear hair protection
(hair net or cap). Long hair can easily be caught in
moving parts.
• Wear fitted clothing; tie buttons on sleeves.
• Do not hold any workpieces in your hands when dril-
ling. Always use a machine clamp or another clamping
tool.
• Protect workpieces and clamping tools on the bench
to prevent them from getting caught. Fasten them
yourself with screws or clamp them to a machine
clamp fastened to the table.
• Check whether the drill holder is tightened properly.
• Check whether cable lead-throughs are okay.
• To remove drill chips only use hand brushes, brushes,
rubber wipers, chip hooks or similar aids.
• Do not carry out any cleaning or greasing work while
the machine is in operation.
• Always keep V-belts covered (so that your hands
cannot become caught).
• Only tighten the toothed ring drill holder by means of
the wrench.
• Never leave the wrench of the drill holder in the drill
holder! Before switching on the machine, check
whether the wrench really has been removed!
• Do not use any drills which are damaged on the
shank.
• Drill is not suitable to use as press!
• If the mains cable is damaged, it may only be replaced
by a mains cable of the same type.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
• Interruption in the mains plug, mains lead or mains
lead damage.
• Defect switch.
• Smoke or stench of scorched isolation.
Voltage | 230 V
Frequency | 50 Hz
Power input | 350 W
No load speed | 580-2650/min
Number of speeds | 5
Chuck capacity/Morse Conical | 13mm/ B-16
Weight | 20 kg
Lpa (sound pressure level) | 62.1 dB(A)
Lwa (sound power level) | 75.1 dB(A)
Vibration value | 1.57 m/s
2
Ferm 3
