Bedienungsanleitung Ferm TSM1032 (Seite 6 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

510129

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

•

When wood residues are trapped between

stationary and moving parts switch the

appliance off and remove the plug from the

electrical socket. Only then remove the residues.

• Select the appropriate saw blade.

• Select the saw blade (with the correct teeth)

and the correct speed of rotation and slip

appropriate for the material to be sawed and

fit the saw blade carefully. This will not only

increase the lifetime of the saw blade but

also prevent cracks and fissures with their

attendant hazards. Fit only recommended saw

blades that meet European standard EN847.

•

Do not saw pegs or sharp-cornered workpieces.

• This is hazardous. Saw pegs or sharp-

cornered workpieces with an appliance

designed for that purpose (a peg cutter or

milling machine) and not with a saw bench.

• Exercise care when sawing waste or firewood.

• Waste or firewood often requires less careful

sawing, so there is a danger that you may not

be quite so alert to irregularities in the wood

and impose too much pressure on the saw.

• Use a table extender for large workpieces.

• When sawing large workpieces, support the

workpiece at table level with a table extender.

• The push-stick or push-block should always

be stored with the machine when not in use.

Examples of problems arising from improper

use of the saw bench

• Contact with rotating saw blade

• This can occur when the protective elements

(such as the protective hood, the protection

under the table surface, the riving knife, the

push stick) are missing or are used improperly.

Improper operation of the protective elements

can result in accidents. When the machine is

switched off, the saw blade may continue to

rotate. There is a risk of your not noticing this

because the appliance falls silent. That is why

the protective hood is so important.

• Recoil of the workpiece

• When the workpiece recoils it may hit those

in the surrounding area at high speed. This

may result in serious or even fatal injury. The

workpiece may recoil for the following reasons

(or a combination of them):

• The saw does not protrude far enough above

the table surface, causing the workpiece to be

guided directly into contact with the teeth of

the saw that is itself moving in the direction of

the user.

• The workpiece seizes on the saw because the

riving knife is not fitted or incorrectly adjusted.

• There is no auxiliary saw rip fence (straight

edge) or it is adjusted incorrectly. Because of

this the wood may become stuck between the

main rip fence and the rotating saw blade.

• Rotating saw blade breaks

• This can be caused by the following factors:

• An improper sawing procedure;

• An improperly adjusted saw blade;

• An improper method of operation;

• Processing material that is unsuitable for the

saw bench.

• Metal parts under voltage

Defective electrical installation may result in metal

parts coming under voltage and causing fire.

• Damage to hearing when noise level is too high

A noise level that is too high may cause

damage to the hearing of persons who are

often close to the saw bench.

• Release of harmful wood dust.

Release of harmful wood dust or glue vapours

may pose health risks. Connect a vacuum

cleaner to the saw bench.

Turn the appliance off immediately in the event of:

• A faulty mains plug, mains flex or flex damage.

• A faulty switch.

• Smoke or smell from scorched insulation.

• Seizing of the saw.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Warning! This machine must be earthed.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1032 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1032

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info