Bedienungsanleitung Festool rs 300 q-plus (Seite 3 von 5) (Englisch)

389419

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

the power tool is used.

If the electric power tool is used for other ap-

plications, with other tools or is not maintained

sufﬁ ciently prior to operation, however, the vibra-

tion and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

3 Power supply and start-up

The mains voltage must correspond to

the speciﬁ cation on the rating plate.

Switch (1.1) serves as an On/Off switch (I = On / 0

= Off). It may be latched with the locking knob on

the side (1.2) for continuous operation. Pressing

the switch again releases the lock.

Always switch the machine off before

connecting or disconnecting the mains

lead!

See Fig. 3 for connection and disconnection of the

power cable.

4 Electronics

The RS 300 EQ has an electronic control

with which the rotational speed can be

varied step-free.

This allows the sanding speed to be adapted to

the optimum level according to the material con-

cerned (see Chapter 6).

The speed is set using the rotary control button

(2.1).

5 Dust extraction

Dust extractors prevent large accumu-

lations of dust in the air in the working

environment and dirt collecting at the

workplace.

5.1 Inboard extraction

The machines are ﬁ tted with inboard extraction as

standard. The sanding dust is extracted through

suction openings in the sanding base (2.4) and

trapped in the turbo-ﬁ lter (1.5). The turbo-ﬁ lter

has to be changed when it is so full of dust that

the extraction power diminishes.

Inserting a turbo-ﬁ lter

- Push the front cardboard section of the turbo-

ﬁ lter with the sealing lip (1.4) onto the extraction

nozzle (1.9) of the ﬁ lter holder

- Insert rear cardboard section with slot (1.6) onto

the retaining strip (1.7) of the ﬁ lter holder

- Push the ﬁ lter holder with its opening (1.11) as

far as it will go onto the extraction nozzle (1.3)

of the machine and clamp tight by turning rotary

knob (1.10).

5.2 External extraction by an extraction

unit

In order to avoid frequent changing of the turbo-

ﬁ lter when carrying longer sanding jobs, it is

possible to connect a Festool extractor to the unit

instead of using inboard extraction. In this case,

the extraction pipe (Ø 27 mm (1.8)) of the extrac-

tion unit is connected to the suction nozzle (1.3).

6 Special sanding pads

The standard sanding pad (93 x 175 mm) can be

exchanged for a special sanding pad. Loosen the

four fastening screws (2.2).

The special sanding shoe is mounted in such a

way that the extended side protrudes over the

front edge of the sander.

6.1 Sanding pad STF-93x230

Please use the enclosed countersunk screws to

secure the STF-93x230 sanding pad instead of the

standard oval-head screws.

The special application of this sanding pad is to

sand in narrow spaces, e.g. between the louvers

on folding shutters or behind heating pipes.

The protruding part of the sanding pad is 60 mm

long and has a Stickﬁ x coating on the top and bot-

tom. Stickﬁ x sandpaper rolls in grit sizes P 50 to

P 180 are available for these applications. These

rolls are 12 m long and can be cut to the desired

length by the customer. Cut through the Stickﬁ x

adhesive coating on the back and the carrier

material using a sharp knife. The sandpaper can

then be simply torn off.

Please note that this sanding pad cannot be used

in conjunction with a suction unit.

6.2 Sanding pad STF-V93x266

The STF-V93x266 sanding pad is fastened with

standard oval-head screws.

This sanding pad has a protruding triangular point

with an edge length of 93 mm it was developed

for sanding in corners and edges though can also

be used on ﬂ at surfaces thanks to its continuous

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool rs 300 q-plus Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info