Bedienungsanleitung Festool TDK 12-12.0 V Li (Seite 12 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574924

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

b) Fitting/removal of chuck on angle

attachment

The chuck is ﬁ tted on the shaft (2.6) of the

angle attachment in the same way as on the

drill spindle of the machine.

3.3 Eccentric attachment DD-ES

The eccentric attachment is used to hold bits.

It allows screwing close to edges.

a) Fitting/removing the eccentric at-

tachment

The eccentric attachment is ﬁ tted/removed in

the same was as the angle attachment (see

Chapter 3.2).

b) Changing tools

- Pull the unlocking ring (2.8) back and remove

the tool and/or insert the new tool.

3.4 CENTROTEC WH-CE toolholder

The CENTROTEC toolholder enables rapid

changes of tools with CENTROTEC shafts.

Do not ﬁ t CENTROTEC tools at the round

shaft section in a conventional chuck to

prevent damage to the shaft.

Danger of injury! When changing

tools, handle the tool and its sharp

cutters with special care and wear pro-

tective gloves, if necessary.

a) Fitting/removing CENTROTEC

Fitting

- Pull the release ring (2.11) forwards, place

the toolholder as far as it will go on the drill

spindle (2.5) and let go of the release ring.

Removal

- Pull the release ring forwards and take off the

toolholder.

b) Changing tools

- To insert or remove a tool with CENTROTEC

shaft, pull the green release ring (2.10) back.

On inserting the tool, turn it until its hex shank

arbour (2.9) locks in place in the hexagonal

shank of the drill spindle, and push the tool

into the toolholder as far as it will go.

3.5 Tool holding fixture in the drill

spindle

Bits can be ﬁ tted directly in the hexagon socket

holder of the drill spindle (2.5) to make the

machine lighter and shorter.

4 Charge battery pack

To load the battery pack, push it into the holder

(3.1) on the charger up to the stop. Perform this

in reverse to remove the battery pack from the

charger. The battery type used (NiCd or NiMH)

is detected automatically. Charging is controlled

by a microprocessor. If a warm NiMH battery

pack (>37° C) is inserted, charging will only be

carried out at a lower charge current. In this

case, the charging time is extended.

The LED (3.2) indicates the respective

charging state of the charger.

LED yellow – steady:

Charger is ready for use.

LED green – ﬂ ashing:

Battery pack being charged.

LED green – steady:

Battery pack fully charged, conservation char-

ge on.

LED red – ﬂ ashing:

General malfunction, e. g. full contact not

being made, short-circuit, battery pack faul-

ty.

LED red – steady:

Temperature of battery pack is outside per-

missible limit.

It is essential that you read the

instructions in the Chapter „Wor-

king instructions - Maintenance

- Care“.

5 Working with the machine

5.1 Initial operation

Turn on by pressing button (1.3). Depending on

the pressure exerted on the button, the adjust-

ment of running speed can be varied inﬁ nitely.

Turn off by releasing the button (1.3).

After releasing the button, the chuck is stopped

and therefore, after-running of the equipment

is prevented.

5.2 Bit storage well

You can insert several bits or bit extensions into

the bit magazine (1.2) from the side.

The magnetic attachment allows you to pick up

screws and similar objects.

6 lnstructions on application - main-

tenance - care

Please pay attention to the fol-

lowing instructions. Otherwise the-

re is a risk of damage to the tool,

charger or battery pack.

- Repairs may only be performed by authorised

technicians. LC 45 charging device: Even after

disconnection from the mains, there is still a

high capacitor voltage on the power output

component on the inside of the device.

- Keep the air vents of the electronic equipment

and the charger clean to guarantee the air

circulation for cooling.

- No metal objects (metal chips) should enter

the charger at the contact points as well as

through the cooling slits into the equipment

(danger of short circuit).

- Only use original Festool battery packs.

Do not use spent and recycled battery packs.

The user shall be liable for damages if Festool

original battery packs are not used.

- Keep the connection contacts of electronic

equipment, charger and battery pack clean.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TDK 12-12.0 V Li Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info