Bedienungsanleitung First Alert 2025F (Seite 3 von 5) (Englisch)

795134

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

InItIAl SetuP

EMERGENCY OVERRIDE KEY USE

Insert emergency override key into

the lock, turn it counterclockwise

and pull the door open.

BATTERY INSTALL

1 Remove battery cover.

2 Install four (4) AA batteries. Make sure to

install them facing the proper direction.

3 Replace the battery cover.

4 When installed correctly, a yellow light

will ash on the digital keypad.

ProgrAmmIng A PerSonAl PASScode

1 Open the safe door.

2 Press the reset button located on the left side of the

battery compartment. (The lock will beep two times

and the yellow light will blink two times).

3 Enter your new three to eight (3-8) digit passcode

followed by ‘A’ or ‘B’. (The lock will beep two times and

the yellow light will blink two times).

NOTE: After pressing the reset button, your passcode must

be programmed within 10 seconds, or it will not be accepted.

LOCKOUT PENALTY:

Green light means correct passcode has been entered. Rapid beeping yellow light

means incorrect passcode has been entered. Entering incorrect passcode three (3)

times will result in lock-out.

IF LOCK-OUT OCCURS:

1 Wait 15 minutes before entering your (3-8) digit passcode.

2 Check to see if the batteries have been installed properly and replace if

necessary.

3 Contact Consumer Aairs at 1-800-323-9005.

Initial Setup Shelf and Mounting

FORGOTTEN PASSCODE

1 Insert override key, turn counterclockwise and pull the door open.

2 Follow instructions on Pg. 3 ‘PROGRAMMING A PERSONAL PASSCODE’ to reset

your passcode.

OPENING SAFE

1 Insert knob key.

2 Enter your three to eight (3-8) digit passcode

followed by ‘A’ or ‘B’.

3 Turn the key clockwise and pull the door open.

CLOSING SAFE

1 Push door closed.

2 Turn knob key counterclockwise fully into locked position.

ImPortAnt Turn the light switch o before closing the safe. Leaving the

light switch on will result in loss of battery power.

ShelF And mountIng

INSTALLING THE SHELF 2072F ONLY

Slide shelf into place on top of shelf racks.

MOUNTING INSTRUCTIONS

1 Remove rubber feet and mounting screws

from safe with Phillip’s head screwdriver.

2 Place your safe where you want it to be mounted. Safe weighs

(36.1 lbs - 2072F; 19.8 lbs. – 2073F; 13.2 lbs. – 2025F) when empty so

be sure that if you’re mounting on a shelf that it will support the weight.

3 Open your safe.

4 Remove the bottom carpet and nd the screw holes.

Mark the safe’s placement through the holes with a pencil.

5 Drill holes in the shelf.

6 Place screws through holes in shelf and rubber feet.

7 Place safe on shelf over the screws and rubber feet. Use a socket wrench

to tighten safe into place.

Beep

AA +

3 4

AA +

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert 2025F Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info