576716

Florabest FBS 43 B2 - IAN 97786 Seite 53

53
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
48
FBS 43 B2
GB
The air fi lter must be checked more frequently if the air is dusty.
1.) Remove the air fi lter housing cover
(see fi g. 10a).
2.) Remove the air fi lter
(see fi g. 10b + 10c).
3.) Clean the air fi lter
by tapping or blowing it out (with compressed air).
4.) Assembly takes place in reverse order.
IMPORTANT!
■ Never clean the air fi lter with petrol or fl ammable solvents.
Spark plug maintenance
1.) Remove the spark plug connector
(see fi g. 11a).
2.) Remove the spark plug using the enclosed spark plug spanner
.
3.) Assembly takes place in reverse order.
Electrode gap = 0.6 mm (distance between the electrodes between which
the ignition spark is generated). Tighten the spark plug with 12 to 15 Nm
of torque using a torque wrench (available from specialist retailers).
Initially check the spark plug for contamination after 10 hours of operation
and clean this with a copper wire brush if required.
Then service the spark plug after every 50 hours of operation.
Grinding the protective hood blade
The protective hood blade
(see fi g. 7a) may become blunt over time.
If you notice that this is the case, loosen the 2 screws used to fasten the
protective hood blade
to the cutting line protective hood . Clamp
the blade in a vice. Grind the blade with a grindstone and ensure that the
correct angle of the blade edge is maintained. Only grind in one direction.
Adjusting the carburettor
The air fi lter housing cover
must fi rst be removed, as displayed in fi g.
10a, before performing any work on the carburettor.
Adjusting the throttle cable
If the device's maximum speed is no longer reached over time and all other
causes in accordance with the "Troubleshooting" section have been ruled
out, this may mean that the throttle cable needs to be adjusted.
NOTE
■
First check whether the carburettor opens completely when the throttle
lever is fully engaged.
This is the case if the carburettor slide (see fi g. 13b) is completely open at
full throttle. Figure 13a shows the correct setting. An adjustment is necessary
if the carburettor slide is not fully open.
The following steps must be taken to adjust the throttle cable:
■ Loosen the locking nut (see fi g. 13a) a few turns. Unscrew the ad-
justing screw (see fi g. 13a) until the carburettor slide is completely
open at full throttle (see fi g. 13b).
■ Retighten the locking nut .
Adjusting the idling rate
IMPORTANT!
■ Adjust the idling rate once the device has warmed up.
If the device does not come to a stop when the throttle is not engaged
and all other causes in accordance with the "Troubleshooting" section
have been excluded, it may mean that a readjustment of the idling rate is
required. Rotate the idling screw
(see fi g. 5a) in a clockwise direction
until the device idles smoothly. If the idling rate is so high that the cutting
tool rotates, this must be reduced by turning the idling screw to the left until
the cutting tool no longer rotates.
Lubricating the gears
■ Add gear grease after every 20 hours of operation (approx. 10 g).
To do so, open the screw (see fi g. 7c).
Spare part orders
Ordering spare parts
The following information must be provided when ordering spare parts:
■ Type of device
■ Item number of the device
■ Device ID number
Current price and information is available at
www.kompernass.com
Storage and transportation
■ Store the device in a safe location.
■ Store the device and accessories in a safe location that is protected
against naked fl ames and sources of heat/sparks, such as gas-powered
water heaters, dryers, oil stoves or mobile heaters, etc.
■ Always keep the cutting blade protective hood , the line spool
and the engine free of mowing residue during storage.
■ Always turn the device off before performing any maintenance work
and remove the spark plug connector .
Storing the device
The device must be prepared for storage if it is to be stored for longer than
30 days. Otherwise the residual fuel in the carburettor will evaporate and
leave a rubbery sediment. This may make starting the device more diffi cult
and result in expensive repair work.
1.) Remove the fi ller cap in order to relieve any pressure in the fuel tank
.
Carefully empty the fuel tank
.
2.) Start the engine and leave it to run until it stops in order to remove all
fuel from the carburettor.
3.) Allow the engine to cool for about 10 minutes.
4.) Remove the spark plug (see "Spark plug maintenance" chapter).
5.) Add 1 teaspoon of 2-stroke oil to the combustion chamber. Pull the
starter pull cord
several times in order to wet all mechanical parts
with oil. Re-insert the spark plug.
NOTE
■ Store the device in a dry place and away from possible ignition
sources.
IB_97786_FBS43B2_LB1.indb 48 03.07.14 15:16
… 53 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

florabest-fbs-43-b2---ian-97786

Suche zurücksetzen

  • je cherche un reservoir d essence pour une d ebroussailleuse fbs 43 b 2 Eingereicht am 2-11-2021 12:00

    Antworten Frage melden

  • Muss man den Rasentrimmer ab und an laden? Auch im Winter Eingereicht am 24-2-2017 16:15

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Florabest FBS 43 B2 - IAN 97786 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info