674625
30
Zoom out
Zoom in
Vorherige Seite
1/136
Nächste Seite
30
GB IE
2. Now push the blow tube (9) on
to the blowing aperture of the
motor housing (1) as far as the
locking device (8).
3. Place the protective cover of the
suction opening (7) on the under-
side of the motor housing. Turn
the protective cover clockwise as
far as it will go.
4. Attach the protective cover by ti-
ghtening the screw with star grip
(18) in the holder.
The screw with star grip has to be
tightened as far as it will go by
hand, as otherwise the leaf blower
cannot be started later.
5. Dismantle the blow tube (9) by
releasing the lock (8) and pulling
off the blow tube forwards.
Assembling/dismantling the
two-piece suction tube
Never use the leaf vacuum
with only one suction tube
section attached. There is a
risk of personal injury!
After the two-part suction
tube has been assembled, it
must not be divided up again
into two parts!
1. Remove the protective cover of
the suction opening by unscrew-
ing the screw with star grip (18)
and turning the protective cover
anti-clockwise and removing it.
2. Assemble the two suction tubes
(16) as illustrated. The parts can
be felt to lock into place.
During assembly, make sure that
the groove on the upper section
of the suction tube is inserted
into the recess provided on the
lower section of the suction tube.
3. Place the suction tube (16) on
the underside of the motor hou-
sing (1). Turn the suction tube
clockwise as far as it will go.
4. Attach the suction tube by tighte-
ning the screw with star grip
(13) in the holder.
The screw with star grip has to be
tightened as far as it will go by
hand, as otherwise the leaf vacuum
cannot be started later.
5. Dismantle the suction tube (16)
by releasing the screw with star
grip (13) und turning the suction
tube anti-clockwise.
Installing/removing the
collection bag
In suction mode the device can only
be operated with the collection bag
installed.
The ventilation opening on the collection bag
(
K L M N O P Q R S T
U V W X Y Z
A B
C D E F G H I J
20) serves for an improved air circulation.
1. If necessary, remove the blower
tube (
K L M N O P Q R S T
U V W X Y Z
A B C D E F G H I J
9) (see „Assembling/dis-
mantling the two-piece blow tube“).
2. Push the catcher (14) on to
the blower outlet of the motor
housing (1) until this snaps into
place in the locking device (8).
3. Hang the fastening hook (15) of
the collection bag (14) on the
holding points (19) provided on
the suction tube.
30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Florabest FLS 3000 B2 - IAN 285190 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info