763957
46
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
287/289
Users Manual
36
To measure capacitance, position the rotary switch to P and set
up the Meter as shown in Figure 19. If the display doesn’t
already indicate the Meter is measuring capacitance, press the
softkey labeled Menu. Next, move the menu selector to the
menu item labeled Diode,Cap and press the softkey labeled
Cap.
Note
To improve measurement accuracy of small value
capacitors, press Menu and move the menu selector
to the menu item labeled REL. With the test leads
open, press the softkey labeled REL to subtract the
residual capacitance of the Meter and leads.
Testing Diodes
W Caution
To avoid possible damage to the meter or to the
equipment under test, disconnect circuit power
and discharge all high-voltage capacitors before
testing diodes.
Use the diode test to check diodes, transistors, silicon controlled
rectifiers (SCRs), and other semiconductor devices. The test
sends a current through a semiconductor junction, and then
measures the junction’s voltage drop. A typical junction drops
0.5 V to 0.8 V.
To test a diode out of a circuit, position the rotary switch to P
and set up the meter as shown in Figure 20. If the display
doesn’t already indicate the Meter is in the Diode Test function,
press the softkey labeled Menu. Next, move the menu selector
to the menu item labeled Diode,Cap and press the softkey
labeled Diode.
If the beeper is enabled during diode test, it will beep briefly for a
normal junction and sound continuously for a shorted junction,
below 0.1 V. See the “Disabling and Enabling the Beeper”
section to disable the beeper.
In a circuit, a similar diode should still indicate a forward-bias
reading of 0.5 V to 0.8 V; however, the reading can vary
depending on the resistance of other pathways between the
probe tips.
Note
R and MIN MAX are disabled when the Meter is
setup for diode test.
46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fluke 289 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Fluke 289

Fluke 289 Bedienungsanleitung - Deutsch - 92 seiten

Fluke 289 Bedienungsanleitung - Holländisch - 90 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info