Bedienungsanleitung Fluke 289 (Seite 59 von 88) (Englisch)

763957

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

True-rms Digital Multimeters

Using Memory

Enabling and Disabling the Smoothing Mode

When an AC input signal is noisy or changes rapidly, the

smoothing mode may display a steadier reading. To enable or

disable the smoothing mode, press the softkey labeled Setup

and position the menu selector next to the menu labeled

Instrument. Next press the softkey labeled Instrument and

position the menu selector next to the menu item labeled

Smoothing. Press the softkey labeled Edit to move the cursor to

the on or off selection. Use 7 and 8 to switch the smoothing

mode on or off.

Using Other Setup Options

Additional setup options hold information about the Meter as well

as some general Meter functions. The Meter Info selection lists

the serial number, model number, firmware version, calibration

date, and calibration counter. Operator name, company name,

site name, and contact information are also displayed when this

information has been loaded into the Meter from FlukeView®

Forms software.

The Calibration selection allows a qualified calibration

technician to enter a password that allows the Meter to be

calibrated. See the 287/289 Calibration Information document to

calibrate the Meter.

The Secure Erase option allows user-accessible memory to be

erased as required by Homeland Security regulations. Meter

calibration is not lost when this low-level erase is performed.

As new Meter features are created, the latest version of software

can be downloaded to the Meter from Fluke’s support web page

using the Software Update option.

Using Memory

The Meter has memory for storing individual measurements,

measurements collected over a specified duration, and

measurement events.

All stored data can be viewed on the Meter or downloaded to a

PC through the Meter’s infrared (IR) communication link using

FlukeView™ Forms. See the “Using Communications” section for

more information on communicating with a PC through

FlukeView Forms software.

Storing Individual Measurement Data

For all measurement functions, a snapshot of the screen data is

saved by pressing the softkey labeled Save. Except for the mini-

measurement in the status bar, the display freezes and the Save

menu appears. Two choices allow either saving the data under a

previously selected name or choosing another name by pressing

the softkey labeled +Name. See the “Naming Saved Data”

section later in this manual. The displayed data is stored along

with the date and time of day the save was performed.

For MIN MAX and Peak, the displayed summary data can be

stored at any time by pressing the softkey labeled Save, thus

preserving a snapshot of the session at that moment.

Naming Saved Data

The Meter has a list of eight preset names under which

measurement data is saved. Multiple records can be saved using

the same name. For example, one preset name is Save. The first

time a save operation is performed with that name, Save-1 is

used to name the record in memory. The next time the Save

name is used, the number increments to 2 and the record is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fluke 289 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fluke 289

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info