763940
93
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
Appendices
Applications A
A-3
If the relative readings value of a dc voltage measurement is shown in the primary
display and the dc voltage itself is shown in the secondary display, the Meter takes a
single measurement and updates both displays with it.
Updating Primary and Secondary Displays with Separate Measurements
If the measurement function in the primary display is different from that in the secondary
display, the Meter updates each display using a separate measurement.
Taking Voltage and Current Measurements Using the Dual Display
Most applications of the dual display listed in Table A-2 can be performed using a single
set of test leads connected to the INPUT VZYR HI and LO terminals. However, to
measure the voltage and current of an input signal requires three leads. Be sure that the
voltage and current measurements share the same common as shown in Figure A-2. Then
simply follow the precautions you would follow if you were making normal current
measurements without a current clamp.
Table A-2. Sample Dual Display Applications
Primary
Display
Secondary
Display Applications
Volts DC Volts AC Monitor dc level and ac ripple of power supply Troubleshoot
amplifier circuits
Volts DC Current DC Check power supply load regulation
Monitor UUT current draw and circuit voltages
Monitor loop current and voltage drop across transmitter
Volts DC Current AC Line and load regulation tests
dc/ac or ac/dc converters
Volts AC Current DC Line and load regulation tests
dc/ac or ac/dc converters
Volts AC Current AC Line and load regulation tests
Transformer (magnetic circuit) saturation
Volts AC Frequency Measure ac amplitude and frequency for line voltage and ac signal
analysis
Measure frequency response of an amplifier
Adjust ac motor control
Read noise in telecommunication applications
Adjust portable power generator to optimize power output
Set frequency compensation for a network
Current DC Current AC Measure ripple and dc current draw of switching power supply
Measure current dissipation in protective fuse resistors used in
power supplies
Measure ripple and noise on a line
MN MX Actual Value Show the minimum or maximum value recorded and the present
measurement
REL Actual Value Show actual measurement and the difference between this value
and the relative base.
93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fluke 8808A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Fluke 8808A

Fluke 8808A Bedienungsanleitung - Deutsch - 102 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info