PR
Proving Unit
Instruction Sheet
Introduction
The PRV240FS Proving Unit (the Product) is an
electronic voltage source. This Product provides
a safe and easy method to verify proper operation
of the T6-600/T6-1000 Electrical
FieldSense technology or other test tools. Use
it to verify either an energized source or a de-
energized source.
known voltage source is available to verify a test
tool.
The Product does not require personal protective
equipment (PPE) unless your environment
requires minimal PPE such as a hard hat, safety
glasses, or ear plugs.
How to Contact Fluke
T
telephone numbers:
●T
(1-800-443-5853)
●Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
●Canada: 1-800-36-FLUKE (1-800-363-5853)
●Europe: +31 402-675-200
●Japan: +81-3-6714-31
●China: +86-400-921-0835
●Singapore: +65-6799-5566
●Anywhere in the world: +1-425-446-5500
Orwww.
T
http://register.
T
supplement, visit
http://us.uke.com/usen/support/manuals.
Safety
A W identies conditions and procedures
that are dangerous to the user
W
T
or personal injury:
●Read all safety information before you
use the Product.
●Carefully read all instructions.
●Do not alter the Product and use only as
specied, or the protection supplied by
the Product can be compromised.
●Do not touch voltages >30 V ac rms,
42 V ac peak, or 60 V dc.
●Do not use the Product around
explosive gas, vapor
environments.
PN 4919689 September 2017
© 2017 Fluke Corporation.
Product specications are subject to change without notice.
All product names are trademarks of their respective companies.
●Do not use the Product if it operates
incorrectly
●Examine the case before you use the
Product. Look for cracks or missing
plastic. Carefully look at the insulation
around the terminals.
●Do not use the Product if it is altered or
damaged.
●Remove the batteries if the Product is
not used for an extended period of time,
or if stored in temperatures above 50 °C.
If the batteries are not removed, battery
leakage can damage the Product.
●Y
door before you operate the Product.
Symbols
Symbols used in the instructions or on the Product
are shown in T
T
Symbol Denition
Consult user documentation.
W
Risk of electric shock.
W
Battery
FieldSense Measurement: Fluke
voltage/current sensing technique.
Certied by CSA
American safety standards.
Conforms to relevant
standards.
Conforms to European Union directives.
Conforms to relevant South Korean EMC
Standards.
This product complies with the WEEE
Directive marking requirements. The
afxed label indicates that you must not
discard this electrical/electronic product
in domestic household waste. Product
Category: With reference to the equipment
types in the WEEE Directive
this product is classed as category 9
"Monitoring and Control Instrumentation"
product. Do not dispose of this product as
unsorted municipal waste.
Operation
T
the Product. See Figure 1 for the location of each
item.
T
Item Description
AFunction selection
B+ T
CAC/DC LED
D − T
ET
FT
GFork saddle
HFinger Ground Contact LED
IFinger Ground Contact
FieldSense Measurement without T
Before verication, set up the T6 for a FieldSense
measurement without the test leads. See the
T6 Quick Reference Guide.
T
1. Move the switch to the FieldSense position.
See Figure 3.
2. Insert the T6 fork into position on the Product.
3. Push and hold the nger ground contact to
activate the Product.
The Product LED turns green and the T6
display shows a 240 V measurement.
FieldSense Measurement with Ground Lead
Before verication, set up the T6 for a FieldSense
measurement with the ground lead. See the
T6 Quick Reference Guide.
T
1. Move the switch to the FieldSense position.
See Figure 4.
2. Insert the T6 fork into position on the Product.
3. Place the black test lead from the test tool
into the test lead ground contact terminal and
press down rmly
The Product LED turns green and the T6
display shows a 240 V measurement.
AC/DC Measurement
Before verication, set up the T6 or other test tool
for ac/dc measurement with the test leads.
T
1. Move the switch to the
See Figure 5.
2. Place the red test lead from the test tool into
the (+) terminal and press down rmly
3. Place the black test lead from the test tool
into the (-) terminal and press down rmly
The Product LED turns green and the T6
display shows a 240 V measurement.
Battery Replacement
Push the nger ground contact button to check the
battery condition. The nger ground contact LED
turns green to show good battery condition. If the
LED does not turn on, replace the batteries.
W
T
personal injury:
●Do not operate the Product with covers
removed or the case open. Hazardous
voltage exposure is possible.
●Repair the Product before use if the battery
leaks.
●Have an approved technician repair the
Product.
T
1. T
symbol aligns with the arrow
2. Lift off the battery door
3. Insert or replace the four
the correct battery orientation.
4. Install the battery door
5. T
symbol aligns with the arrow
Specications
Output voltage
240 V ac rms or dc ........... ±10 % ≥1 MΩ
LED power indicator ......... Turns on when output voltage is
present
Battery ................................... 4 x
15
Battery life ............................. 3 hr based on a 10 s test cycle or
1
Operating temperature ..... -10 °C to +50 °C
Operating humidity ........... 0 % to 90 % (0 °C to 35 °C)
0 % to 70 % (35 °C to 55 °C)
Operating altitude ............. 2000 m
Dimensions ....................... 1
(4.6 in x 2.9 in x 1.75 in)
Weight ................................ 0.32 kg (12 oz) includes batteries
Safety
General ............................ IEC 61010-1, Pollution Degree 2
Measurement ................... IEC 61010-2-030
240 Vrms/240 Vdc
Electromagnetic Compatibility (EMC)
International ...................... IEC 61326-1: Controlled
Electromagnetic Environment
CISPR 1
Group 1: Equipment has intentionally generated and/or uses
conductively-coupled radio frequency energy that is necessary
for the internal function of the equipment itself.
Class A: Equipment is suitable for use in all establishments
other than domestic and those directly connected to a low-
voltage power supply network that supplies buildings used
for domestic purposes. There may be potential difculties in
ensuring electromagnetic compatibility in other environments
due to conducted and radiated disturbances.
Caution: This equipment is not intended for use in residential
environments and may not provide adequate protection to
radio reception in such environments.
Emissions that exceed the levels required by CISPR 1
occur when the equipment is connected to a test object.
Korea (KCC) ....................... Class
Broadcasting & Communication
Equipment)
Class A: Equipment meets requirements for industrial
electromagnetic wave equipment and the seller or user
should take notice of it. This equipment is intended for use in
business environments and not to be used in homes.
USA .......................... 47 CFR 15 subpart B. This
product is considered an exempt
device per clause 15.103.
LIMITED W
This Fluke product will be free from defects in material
and workmanship for one year from the date of purchase.
This warranty does not cover fuses, disposable batteries,
or damage from accident, neglect, misuse, alteration,
contamination, or abnormal conditions of operation or
handling. Resellers are not authorized to extend any other
warranty on Fluke’s behalf. T
warranty period, contact your nearest Fluke authorized service
center to obtain return authorization information, then send
the product to that Service Center with a description of the
problem.
THIS WARRANTY
WARRANTIES, SUCH
PURPOSE,
LIABLE FOR
CONSEQUENTIAL DAMAGES OR LOSSES,
ANY CAUSE OR THEOR
do not allow the exclusion or limitation of an implied warranty
or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation Fluke Europe B.V
P P
Everett, WA 5602 BD Eindhoven
U.S.A. The Netherlands
1
Fluke Corporation certies this Product was tested and
veried with applicable calibration procedures during the
manufacturing process. Fluke’s quality system controls these
procedures.
The instruments used during the testing and calibration of
this Product are traceable to SI units through internationally
recognized measurement standards.
This document is not a certicate of calibration or traceability
T
Fluke service center to process an order to have your
Product returned for calibration.
calibration service.
