SAFETY PRECAUTIONS
Explanation of Symbols on the product
Warning
Read the user instructions carefully to
make sure you understand all the
controls and what they do.
Do not operate in the rain or leave the
product outdoors while raining.
Switch off! Remove plug from mains
before adjusting, cleaning or if cable is
entangled or damaged
The use of eye protection is
recommended to protect against objects
thrown by the cutting parts.
General
1. Never allow children or people unfamiliar with
these instructions to use the product. Local
regulations may restrict the age of the operator.
2. Only use the product in the manner and for the
functions described in these instructions.
3. Never operate the product when you are tired, ill
or under the influence of alcohol, drugs or
medicine.
4. The operator or user is responsible for
accidents or hazards occurring to other people
or their property.
Electrical
1. The British Standards Institute recommend the
use of a Residual Current Device (R.C.D.) with a
tripping current of not more than 30mA. Even
with a R.C.D. installed 100% safety cannot be
guaranteed and safe working practice must be
followed at all times. Check your R.C.D. every
time you use it.
2. Before use, examine cable for damage, replace
it if there are signs of damage or ageing.
3. Do not use the product if the electric cables are
damaged or worn.
4. Immediately disconnect from the mains
electricity supply if the cable is cut, or the
insulation is damaged. Do not touch the electric
cable until the electrical supply has been
disconnected. Do not repair a cut or damaged
cable. Replace it with a new one.
5. Your electric cable must be uncoiled, coiled
cables can overheat and reduce the efficiency of
your product.
6. Keep the cable clear of the cutting area and
obstacles at all times.
7. Never carry the product by the cable.
8. Never pull on the cable to disconnect any of the
plugs
9. Do not pull cable around sharp objects.
10. Always switch off at the mains before
disconnecting any plug, cable connector or
extension cable.
11. Switch off, remove plug from mains and
examine electric supply cable for damage or
ageing befor
e winding cable for storage. Do
not repair a damaged cable, replace it with a
new one. Use only Husqvarna Outdoor
Products replacement cable.
12. Always wind cable carefully, avoiding kinking.
13. Use only on AC mains supply voltage shown on
the product rating label.
14. Our products are double insulated to EN50144.
Under no circumstances should an earth be
connected to any part of the product.
Cables
Use only 1.00mm
2
size cable up to 40 metres length
maximum.
Maximum rating:
1.00mm
2
size cable 10 amps 250 volts AC
1. Mains cables and extensions are available from
your local Approved Service Centre.
2. Only use extension cables specifically designed
for outdoor use.
Preparation
1. Always wear suitable clothing, gloves, and stout
shoes. The use of safety glasses is
recommended. Do not wear loose clothing or
jewellery which can be caught in moving parts.
2. Thoroughly inspect the area where the product
is to be used and remove all wires and other
foreign objects.
3. Before using the machine and after any impact,
check for signs of wear or damage and repair
as necessary.
4. Always ensure the hand guard supplied is fitted
before using the product. Never attempt to use
an incomplete product or one with an
unauthorised modification.
Use
1. Use the product only in daylight or good artificial
light.
2. Avoid operating your product on a wet hedge,
where feasible.
3. Know how to stop the product quickly in an
emergency.
4. Never hold the product by the guard.
5. Never operate the product with damaged guards
or without guards in place.
6. Remove plug from mains befor
e passing
product to another person.
7. Avoid operating while people especially children
are nearby.
8. Whilst using the product always be sure of a
safe and secure operating position.
Do not
overreach. Keep proper footing and balance at
all times.
9. Keep hands and feet away from the cutting
If not used properly this product can be dangerous. The warnings and safety instructions must be
followed to ensure reasonable safety and efficiency in using this product. The operator is responsible
for following the warnings and instructions in this manual and on the product. Never use the product
unless the guards provided by the manufacturer are in the correct position.
ENGLISH - 1
