Zoom out
Zoom in
Vorherige Seite
1/17
Nächste Seite
FORD C-MAX Quick Reference Guide
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Forum

Suche zurücksetzen

  • ich benötige die navi betriebsanleitung für ford c max 2010. Eingereicht am 26-2-2021 14:49

    Antworten Frage melden
  • Wo befindet sich die Ölablassschraube beim Ford C-Max Eingereicht am 13-5-2020 12:21

    Antworten Frage melden
  • Haben Nebelleuchten eine Kontrolldiode und hat das Auto eine Frostwarnanzeige Eingereicht am 7-11-2017 11:19

    Antworten Frage melden

Inhalt der Seiten


  • Page 1

    FORD C-MAX Quick Reference Guide



  • Page 2

    About This Quick Reference Guide
    We have created this guide to help you get to know certain
    features of your vehicle. It only contains basic instructions
    to get you started and is not a substitute for the Owner's
    Manual.
    You must read the full instructions in the Owner's Manual
    along with all the warnings. The more that you know about
    your vehicle, the greater the safety and pleasure you will get
    from driving it.
    Thank you for choosing Ford.
    WARNING
    Driving while distracted can result in loss of vehicle control, crash and injury. We strongly
    recommend that you use extreme caution when using any device that may take your focus off
    the road. Your primary responsibility is the safe operation of your vehicle. We recommend against
    the use of any hand-held device while driving and encourage the use of voice-operated systems when
    possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices
    while driving.
    Note: This guide describes product features and options available throughout the range of available models,
    sometimes even before they are generally available. It may describe options not fitted to the vehicle you
    have purchased.
    Note: Some of the illustrations in this guide may show features as used in different models, so may appear
    different to you on your vehicle. However, the essential information in the illustrations is always correct.
    Note: Always use and operate your vehicle in line with all applicable laws and regulations.
    The information contained in this publication was correct at the time of going to print. In the interest of
    continuous development, we reserve the right to change specifications, design or equipment at any time
    without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a
    retrieval system or translated into any language in any form by any means without our written permission.
    Errors and omissions excepted.
    © Ford Motor Company 2015
    All rights reserved.
    Part Number: CG3643en 02/2015 20150213105214



  • Page 3

    INSTRUMENT PANEL OVERVIEW

    1

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 4

    A

    Air vents.

    B

    Direction indicator lever.

    C

    Information display control.

    D

    Instrument cluster.

    E

    Audio control.

    F

    Wiper lever.

    G

    Information and entertainment display.

    H

    Audio unit.

    I

    Hazard flasher switch.

    J

    Climate controls.

    K

    Keyless start button.

    L

    Horn.

    M

    Steering wheel adjustment.

    N

    Cruise control switches.

    O

    Lighting control.
    Unlocking the Doors

    LOCKING AND UNLOCKING

    Press the button to unlock all
    doors. The direction indicators
    will flash.

    Power Door Locks
    The power door lock control is on the driver
    door.

    Note: You can unlock the driver's door with
    the key. Use the key when the remote control
    is not functioning.
    Note: When you lock your vehicle for several
    weeks, the remote control will be switched
    off. Your vehicle must be unlocked and
    started. Unlocking and starting your vehicle
    once will enable the remote control.
    Locking the Doors
    Press the button to lock all the
    doors. The direction indicators
    will flash.

    A

    Unlock.

    B

    Lock.

    Note: If any door or the luggage
    compartment is not closed, or if the hood is
    not closed on vehicles that have an anti-theft
    alarm or remote start, the direction indicators
    will not flash.

    Remote Control
    You can use the remote control at any time
    while your vehicle is switched off.

    2

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 5

    Type One

    Double Locking
    Double locking is a theft protection feature
    that prevents someone from opening the
    doors from the inside. You can only double
    lock the doors if they are all closed.
    Press the button twice within
    three seconds.

    Locking and Unlocking the Doors
    with the Key
    Locking with the Key
    Turn the top of the key toward the front of
    your vehicle.
    Double Locking with the Key
    Turn the key to the lock position twice
    within three seconds.

    A

    Volume up.

    B

    Seek up or next.

    C

    Volume down.

    D

    Seek down or previous.

    Type Two

    Unlocking with the Key
    Turn the top of the key toward the rear of
    your vehicle.
    Note: If the child safety locks are on and you
    pull the interior handle, you will only turn off
    the emergency locking, not the child safety
    lock. You can only open the doors using the
    external door handle.

    AUDIO CONTROL
    Select the required source on the audio unit.
    You can operate the following functions
    with the control:

    A

    Volume up.

    B

    Seek up or next.

    C

    Volume down.

    D

    Seek down or previous.

    E

    Press to select source.

    Seek, Next or Previous
    Press the seek button to:
    • Tune the radio to the next or previous
    stored preset.
    • Play the next or the previous track.

    3

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 6

    Intermittent Wipe

    Press and hold the seek button to:
    • Tune the radio to the next station up or
    down the frequency band.
    • Seek through a track.

    INFORMATION DISPLAY
    CONTROL

    A

    Short-wipe interval.

    B

    Intermittent wipe.

    C

    Long-wipe interval.

    Push the wiper lever up to switch the wipers
    on, and then use the rotary control to adjust
    the intermittent wipe interval.

    WINDSHIELD WIPERS

    A

    Single wipe.

    B

    Intermittent wipe.

    C

    Normal wipe.

    D

    High-speed wipe.

    AUTOWIPERS

    A

    Highest sensitivity.

    B

    On.

    C

    Lowest sensitivity.

    Switch the autowipers on by moving the
    wiper lever up to the first position.

    Note: Move to position O marked on the
    wiper lever to switch off.

    Switch the autowipers off by moving the
    wiper lever down.

    4

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 7

    Rear Window Washer

    Use the rotary control to adjust the
    sensitivity of the rain sensor:
    • Rotate the control down to low
    sensitivity, and the wipers turn on when
    the rain sensor detects a large amount
    of moisture on the windshield.
    • When you move the wiper lever up
    to the first position and the
    autowiper system is on, the
    autowiper sensitivity setting adjusts
    the wiper speed according to the
    moisture on the windshield only.
    • When you lower the sensitivity, the
    wipers remain in their ready position
    only. They do not wipe the
    windshield automatically unless the
    sensor detects moisture.
    • Move the wiper lever position up to
    the second position to wipe the
    windshield on-demand.
    • Rotate the control up to high sensitivity,
    and the wipers turn on when the rain
    sensor detects a small amount of
    moisture on the windshield.
    • When you set the wiper control to a
    higher sensitivity, the wipers wipe
    the windshield once.
    • Remember to move the wiper lever
    position up to the second position
    to wipe the windshield on-demand.

    POWER WINDOWS
    To reduce wind noise or buffeting when just
    one window is open, open the opposite
    window slightly.

    One-Touch Down (If Equipped)
    Press the control fully and release it. Press
    again or lift it to stop the window.

    One-Touch Up (If Equipped)
    Lift the control fully and release it. Press or
    lift it again to stop the window.

    GLOBAL OPENING AND
    CLOSING

    REAR WINDOW WIPER AND
    WASHERS

    Global Opening
    To open all the windows:

    Rear Window Wiper

    1.

    Press and release the remote control
    unlock button.
    2. Press and hold the remote control
    unlock button for at least three seconds.
    Press the lock or unlock button to stop the
    opening function.

    Global Closing
    Vehicles Without Keyless Entry
    A

    Intermittent wipe.

    B

    Low speed wipe.

    C

    Off.

    To close all the windows, press and hold
    the remote control lock button for at least
    three seconds. Press the lock or unlock
    button to stop the closing function.
    5

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 8

    Vehicles With Keyless Entry

    REAR SEATS

    To close all the windows, press and hold
    the driver’s door handle for at least three
    seconds.

    Second row seats - C-MAX
    1.

    Remove the luggage cover.

    HEATED WINDOWS AND
    MIRRORS
    Heated Rear Window
    Press the button to clear the
    window of thin ice and fog. It will
    switch off automatically after a
    short period of time. Make sure the engine
    is running before operating the heated
    windows.
    Note: Do not use razor blades or other sharp
    objects to clean the inside of the rear window
    or to remove decals from the inside of the
    rear window. This may cause damage to the
    heated grid lines and will not be covered by
    your warranty.

    Heated Exterior Mirrors (If Equipped)
    They will switch on
    automatically when you switch
    the heated rear window on.

    2. Pull the release lever on the underside
    of the seat.

    Note: Do not remove ice from the mirrors
    with a scraper or attempt to readjust the
    mirror glass if it is frozen in place. These
    actions could cause damage to the glass and
    mirrors.
    Note: Do not clean the housing or glass of
    any mirror with harsh abrasives, fuel or other
    petroleum-based cleaning products.

    HEATED WINDSHIELD
    Press the button to clear the
    heated windshield of thin ice and
    fog. The heated windshield will
    automatically turn off after a short period
    of time. Start the engine before you switch
    the heated windshield on.

    Note: The complete seat moves rearward
    as the seat cushion is folded up.
    3. Fold the seatback until it engages.

    6

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 9

    Note: As the seats slide rearward, they also
    move slightly inboard.
    4. Pull the lever on the outer front edge of
    the outboard seats and push the seats
    rearward.
    2. Pull the strap and lift the right-hand
    seat cushion.

    To return the seats to the forward position,
    pull the lever and slide the seats forward.
    To return the center seat to its original
    position, pull the lever on the underside of
    the seat. Fold the center seat forward and
    push it back down fully until it engages.
    Install the luggage cover.

    Second row seats - Grand C-MAX
    Stowing the center seat

    3. Pull the strap to fold the center seat
    over into the right-hand seat base.
    4. Fold the right-hand seat cushion down.
    Note: You can use the space between the
    outboard seats to access the third row seats
    when the center seat has been stowed.
    Folding the seats forward
    1.

    Note: The center seat must be stowed into
    the right-hand seat base before the
    right-hand seat is folded.

    Pull the lever on the back of the center
    seat and push the seatback down until
    it locks.

    7

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 10

    Press the push button ignition switch once
    without your foot on the brake or clutch
    pedal. It is on the instrument panel near
    the steering wheel. All electrical circuits
    and accessories are operational and the
    warning lamps and indicators illuminate.
    Press the push button ignition switch again
    without your foot on the brake or clutch
    pedal to switch the ignition off.

    Starting Your Vehicle
    Vehicles with Manual Transmission
    1. Fully depress the clutch pedal.
    2. Briefly press the push button ignition
    switch.
    Note: Releasing the clutch pedal during
    engine starting stops the engine from
    cranking.
    1. Pull the strap and lift the cushion.
    2. Lift the lever and push the seatback
    down until it locks.

    Vehicles with Automatic Transmission
    1. Shift into park (P).
    2. Fully depress the brake pedal.
    3. Briefly press the push button ignition
    switch.
    Note: Releasing the brake pedal during
    engine starting stops the engine from
    cranking.

    PUSH BUTTON IGNITION
    SWITCH
    Switching the Ignition On to
    Accessory Mode

    Vehicles with a Diesel Engine
    Note: Engine cranking will not start until the
    engine glow plug warning lamp turns off.
    This may take several seconds in extremely
    cold conditions.

    Stopping the Engine When Your
    Vehicle is Moving
    1.

    Press and hold the push button ignition
    switch, or press it three times within two
    seconds.
    2. Shift into neutral and use the brakes to
    bring your vehicle to a safe stop.
    3. When your vehicle has stopped, shift
    into park (P) and switch the ignition off.

    8

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 11

    AUTO-START-STOP

    To Re-Start the Engine

    Switching the System On and Off

    Release the brake pedal or press the
    accelerator pedal.

    HILL START ASSIST
    The system makes it easier to pull away
    when your vehicle is on a slope without the
    need to use the parking brake.

    When you switch the ignition on, the system
    automatically turns on.
    To switch the system off, press the switch
    and the word OFF illuminates. Press again
    to switch the system back on. The system
    only switches off for the current ignition
    cycle.

    When the system is active, your vehicle
    remains stationary on the slope for two to
    three seconds after you release the brake
    pedal. This allows time to move your foot
    from the brake to the accelerator pedal.
    The system releases the brakes
    automatically once the engine has
    developed sufficient drive to prevent your
    vehicle from rolling down the slope. This is
    an advantage when pulling away on a
    slope, for example from a car park ramp,
    traffic lights or when reversing uphill into a
    parking space.

    Using Auto-Start-Stop Manual
    Transmission
    To Stop the Engine
    1. Stop your vehicle.
    2. Shift into neutral.
    3. Release the clutch and accelerator
    pedal.

    Switching the System On and Off

    To Re-Start the Engine

    Vehicles with Manual Transmission

    Press the clutch pedal.

    You can switch this feature on or off in the
    information display. The system remembers
    the last setting when you start your vehicle.

    Note: To obtain maximum benefit from the
    system, move the transmission lever to
    neutral and release the clutch pedal during
    any stop of longer than three seconds.

    Vehicles with Automatic Transmission

    Note: Start-stop also comes with stall
    recovery. If you fully depress the clutch pedal
    after stalling the engine, the engine
    automatically restarts.

    You cannot turn the system on or off. When
    you switch the ignition on, the system
    automatically turns on.

    Using Auto-Start-Stop Automatic
    Transmission

    ACTIVE PARK ASSIST
    Using Active Park Assist - Parallel
    Parking

    To Stop the Engine
    1. Stop your vehicle in drive (D).
    2. Release the accelerator pedal.
    3. Maintain pressure on the brake pedal.
    Note: The engine will also shut down if the
    gearshift lever is in park (P) or neutral (N)
    regardless of brake pedal position.

    Press the button located on the
    center console near the gearshift
    lever or the right side of the
    center stack once.

    9

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 12

    When driving at a speed less than 22 mph
    (35 km/h) the system automatically scans
    both sides of your vehicle for an available
    parking space. The system displays a
    message and a corresponding graphic to

    indicate it is searching for a parking space.
    Use the direction indicator to select
    searching either to the left-hand side or
    right-hand side of your vehicle.

    Using Active Park Assist Perpendicular Parking

    Using Active Park Assist - Park Out
    Assist
    While your vehicle is at rest in a
    parallel parking space, press the
    active park assist button.

    Press the button located on the
    center console near the gearshift
    lever or the right side of the
    center stack twice.

    The system displays a message requesting
    an indication of direction. Use the direction
    indicator to signal which side of your vehicle
    you want to exit the parking space.

    The system displays a message and a
    corresponding graphic to indicate it is
    searching for a parking space. Use the
    direction indicator to select searching either
    to the left-hand side or right-hand side of
    your vehicle.

    REAR VIEW CAMERA

    Note: If you do not make a selection the
    system will default to the passenger's side.

    The rear view camera provides an image of
    the area behind your vehicle.

    When the system finds a suitable space, it
    displays a message and a tone sounds.
    Stop your vehicle and follow the
    instructions on the screen. If your vehicle is
    moving very slowly, you may need to pull
    forward a short distance before the system
    is ready to park.

    During operation, lines appear in the display
    which represent your vehicle’s path and
    proximity to objects behind your vehicle.

    Using the Rear View Camera
    System
    The rear view camera system displays what
    is behind your vehicle when you shift the
    transmission into reverse (R).
    Note: The reverse sensing system is not
    effective at speeds above 7 mph (12 km/h)
    and may not detect certain angular or
    moving objects.

    10

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 13

    The system uses three types of guides to
    help you see what is behind your vehicle:
    • Active guidelines: Show the intended
    path of your vehicle when reversing.
    • Fixed guidelines: Show the actual path
    your vehicle is moving in while reversing
    in a straight line. This can be helpful
    when backing into a parking space or
    aligning your vehicle with another object
    behind you.
    • Centerline: Helps align the center of
    your vehicle with an object (for
    example, a trailer).

    USING CRUISE CONTROL

    Note: If the transmission is in reverse (R)
    and the luggage compartment door or
    liftgate is open, no rear view camera features
    will display.

    The cruise controls are on the steering
    wheel.

    Switching Cruise Control On

    Note: When towing, the camera only sees
    what you are towing. This might not provide
    adequate coverage as it usually provides in
    normal operation and some objects might
    not be seen. In some vehicles, the guidelines
    may disappear when you connect the trailer
    tow connector.

    Press and release the cruise control icon.
    The indicator appears in the
    instrument cluster.
    Setting the Cruise Speed
    1. Drive to desired speed.
    2. Press and release SET+ or SET-.
    3. Take your foot off the accelerator pedal.
    Note: The indicator will change color.

    Manual Zoom
    Selectable settings for this feature are
    Zoom in (+) and Zoom out (-). Press the
    symbol in the camera screen to change the
    view. The default setting is Zoom OFF.

    Note: Cruise control will disengage if your
    vehicle speed decreases more than 10 mph
    (16 km/h) below your set speed while driving
    uphill.

    This allows you to get a closer view of an
    object behind your vehicle. The zoomed
    image keeps the bumper in the image to
    provide a reference. The zoom is only active
    while the transmission is in reverse (R).

    Changing the Set Speed

    Camera System Settings



    You can adjust the camera settings using
    the vehicle settings menu in the information
    display.





    Press and release SET+ or SET-. The
    set speed will change in approximately
    5 mph (5 km/h) increments.
    Press the accelerator or brake pedal
    until you reach the desired speed. Press
    and release SET+ or SET-.
    Press and hold SET+ or SET-. Release
    the control when you reach the desired
    speed.

    Note: If you accelerate by pressing the
    accelerator pedal, the set speed will not
    change. When you release the accelerator
    pedal, your vehicle returns to the speed that
    you previously set.
    11

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 14

    Canceling the Set Speed

    Cross Traffic Alert also sounds a series of
    tones and a message appears in the
    information display indicating a vehicle is
    coming from the right or left. Cross Traffic
    Alert works with the reverse sensing system
    that sounds its own series of tones.

    Press and release CAN to place the system
    in standby mode. The system will not erase
    the set speed.
    Resuming the Set Speed
    Press and release RES.

    ACTIVE CITY STOP

    Switching Cruise Control Off

    Principle of Operation

    Press and release the cruise control icon,
    when the system is in stand by mode or
    switch the ignition off.

    The sensor is on the rear of the interior
    mirror. It continuously monitors conditions
    to decide when to intervene.

    Note: You erase the set speed when you
    switch the system off.

    The system operates at speeds below
    approximately 31 mph (50 km/h) by
    applying the brakes if it detects that a crash
    is likely. If the system applies the brakes a
    message will appear in the information
    display.

    BLIND SPOT INFORMATION
    SYSTEM
    Blind Spot Information System
    (BLIS™) with Cross Traffic Alert

    The system may reduce the risk of a low
    speed crash into another vehicle. It also
    helps reduce impact damage or may avoid
    the crash completely.

    Switching the Systems Off and On
    You can temporarily switch off one or both
    systems in the information display. When
    you switch off the Blind Spot Information
    System, you will not receive alerts and the
    information display will display a system
    off message.

    Note: You must depress the brake pedal to
    obtain full braking force.

    Switching the System Off and On
    You can switch this feature off using the
    information display controls.

    One or both systems cannot be switched
    off when MyKey is used.

    Note: The system automatically turns on
    every time you switch the ignition on.

    System Lights and Messages

    In certain situations we recommend that
    you switch the system off, for example:
    • Driving off-road when objects may
    cover the windshield.
    • Driving through a car wash facility.

    MAINTENANCE
    WARNING
    Keep your hands and clothing clear
    of the engine cooling fan.
    The system displays a yellow warning
    indicator located in the exterior mirrors.

    Note: Under certain conditions, the fan may
    continue to run for several minutes after you
    have switched the engine off.
    12

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 15

    As a driver assistance feature, your vehicle
    has a tire pressure monitoring system. A
    warning lamp will illuminate when one or
    more of the tires are significantly
    under-inflated. If the low tire pressure
    warning lamp illuminates, you should stop
    your vehicle as soon as it is safe to do so,
    check the tires and inflate them to the
    correct pressure.

    CHANGING THE WIPER BLADES
    Setting the Front Wipers in the
    Service Position
    1.

    Make sure that the outside of the
    windshield is free from snow and ice.
    2. Switch on the ignition.

    Driving on under-inflated tires can:
    • Cause them to overheat.
    • Lead to tire failure.
    • Reduce fuel efficiency.
    • Reduce tire life.
    • Affect vehicle handling or stopping
    ability.
    The system is not a substitute for correct
    tire maintenance.
    You must maintain the correct tire
    pressures, even if low tire pressure has not
    illuminated the warning lamp.

    3. Switch off the ignition and within three
    seconds, pull the wiper lever to toward
    you. Hold the lever in until wipers have
    moved to the service position.

    Understanding the Tire Pressure
    Monitoring System
    The system measures the pressure in the
    four road tires and sends the tire pressure
    readings to your vehicle.
    The system detects this lower pressure as
    being significantly below the correct
    inflation pressure and the warning lamp
    illuminates. You must inflate the tires to
    the correct pressure.
    If the Warning Lamp is On:

    4. Release the lever when the wipers have
    moved to the service position.

    1.

    Check each tire to verify that none are
    flat.
    2. If one or more tires are flat, repair as
    necessary.
    3. Check the tire pressures and inflate all
    the tires to the correct pressure.
    4. Carry out the tire pressure monitoring
    system reset procedure.

    TIRE PRESSURE MONITORING
    SYSTEM

    13

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 16

    Tire Pressure Monitoring System
    Reset Procedure

    Carrying Out the System Reset
    Procedure

    You must carry out the system reset
    procedure after each tire replacement or
    adjustment of the tire pressures.

    1.

    Check the tire pressures and inflate all
    the tires to the correct pressure.
    2. Use the information display controls on
    the steering wheel or instrument panel.

    To reset the tire pressure monitoring system, scroll to:
    Message

    Description and Action

    Settings

    Press the OK button.

    Driver assist

    Press the OK button.

    Tire Monitor

    Press and hold the OK button until confirmation appears.
    Alternatively, if your vehicle has a tire pressure monitoring
    system reset button, press and hold the button until confirmation appears.

    PHONE
    Pairing Your Cell Phone for the First
    Time
    The first thing you must do to use the phone
    features of SYNC is to pair your
    Bluetooth-enabled cell phone with SYNC.
    This allows you to use your cell phone in a
    hands-free manner.
    Touch the upper left corner of the touchscreen:
    Menu Item

    Action and Description

    Pair phone
    Find SYNC

    Follow the on-screen instructions.
    Make sure that Bluetooth is set to On and that your cell phone
    is in the correct mode. See your cell phone’s manual if necessary.
    Select SYNC and a six-digit PIN appears on your device.
    If you are prompted to enter a PIN on your device, it does not
    support Secure Simple Pairing. To pair, enter the PIN displayed
    on the touchscreen. Skip the next step.
    When prompted on your cell phone’s display, confirm that the
    PIN provided by SYNC matches the PIN displayed on your cell
    phone.
    The display indicates when the pairing is successful.
    SYNC may prompt you with more cell phone options. For more
    information on your cell phone's capability, see your cell
    phone's manual and visit the website.
    14

    C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing



  • Page 17

    CG3643en






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ford C-Max 2015 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Ford C-Max 2015 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 16,36 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Ford C-Max 2015

Ford C-Max 2015 Bedienungsanleitung - Deutsch - 492 seiten

Ford C-Max 2015 Bedienungsanleitung - Deutsch - 19 seiten

Ford C-Max 2015 Bedienungsanleitung - Englisch - 444 seiten

Ford C-Max 2015 Kurzanleitung - Holländisch - 19 seiten

Ford C-Max 2015 Bedienungsanleitung - Holländisch - 356 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info