Bedienungsanleitung Frigicoll PCO-Kit (Seite 4 von 6) (Englisch)

771574

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Instructions For Use

Note: The end of life of the UV-C tube will affect the sterilization effect. Be sure to

replace the UV-C tube.

OFF ON

Set

Power

Life Span.

Error Code

PCO-kit

OFF ON

Set

Power

Life Span.

Error Code

PCO-kit

Power

Swicth Key

Power

Swicth Key

Digital

Tube

Digital

Tube

Set

Button

Set

Button

Power on, and turn on the PCO-kit power switch, the digital tube displays the

current mode: U1 mode or U2 mode (display 10s). This product defaults to U1

mode. If you need to switch to another mode, you can set it by pressing the

button "Set". When it is pressed for the rst time, the current mode is displayed

and blinks; when it is pressed for the second time, it switches to other modes.

Wait until it does not blink, then power off and Restart, PCO-kit will work in the

new mode.

In any mode, within 25s of starting the PCO-kit, the digital tube displays the life

value (no fault code is displayed), and the PCO-kit will work or standby (when

there is no wind in the air duct, the PCO-kit will be in standby) .

The difference between PCO-kit working in U1 mode and U2 mode is shown in

the table below.

System Monitoring Failure

Mode

Error Code U1 U2

Er-1

Er-2 X

Er-3 X

Er-4 X

Er-5

Note: means monitoring, X means not monitoring.

lnstallation Method

Warning

Please cut off the power before installation.

Installation tools:Impact drill, Electric batch, Wiring tool, 75mm diameter

iron hole opener, Screwdriver, etc.

>1.5m

Duct

Hole card Air outlet

Accessory

Port

Alarm Port

Control Port

Air conditioning

controller

Note: The equipment connection needs

to share the ground.

1. Paste the hole card on the air duct. And conrm that the distance between the

PCO-kit and the air outlet is greater than 1.5m.

2. Use a percussion drill to drill the hole, and the size of the hole is consistent with

that of the hole card.

3. Insert the PCO-kit into the air duct with the hole, and x it with 4 M4 screws.

(Note: When installing, the front direction should be easy to check.)

4. Make sure that the high-voltage power supply has been cut off. Connect the

alarm signal wire and control signal to the accessory prot. Insert the accessory

port into the signal port on the back of the PCO-kit in the direction of the notch.

(Note: The alarm signal line should be connected to the signal ports 1 and 2 of

PCO-kit, and the control signal line should be connected to the signal ports 3

and 4.)

5. Connect the power cord on the PCO-kit to the Mains grid distribution box, pay

attention to the yellow-green wire and ground wire.

6. Power on, turn on the power switch on the PCO-kit to the "ON" position, turn on

the air conditioner, and check whether it lights up normally after 30s.

(Note: When it is normally lit, the digital tube displays numbers)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frigicoll PCO-Kit Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info