Bedienungsanleitung Fujitsu DL3600 (Seite 1 von 2) (Englisch)

20111

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

OSE Fujitsu DL3600

Print method 24-pin impact dot matrix

Print speed 300 cps @ 10 cpi, 360 cps @ 12 cpi, high-speed draft;

90 cps @ 10 cpi, 108 cps @ 12 cpi, letter quality

Resolution 360 dpi

Fonts Eight resident fonts plus downloadable fonts and optional

plug-in font cards

Paper Handling Rear push tractor feed, friction feed. Up to five-part

forms, maximum thickness 0.33 mm

Interfaces CENTRONICS parallel or RS-232C serial

Emulations Fujitsu DPL24C PLUS, IBM Proprinter XL24, Epson

LQ-2500 and LQ-2550

Options CENTRONICS parallel and RS-232C serial interface, cut

sheet feeder, font and emulation cards, color kit

Control Panel

POWER light: Indicates printer is on.

ONLINE light: Indicates printer is ready to receive data.

PAPER OUT light: Indicates printer is out of paper.

LETTER and DRAFT lights: Indicate which print quality, letter or draft, is

selected.

FONT1 and FONT2 lights: Indicate which user-defined font/pitch combination

is selected.

MENU1 and MENU2 lights: Indicate which user-defined print feature set is

selected.

ONLINE key: Press to toggle printer online and offline.

FF key: Press to advance continuous feed paper one page or to eject a single

sheet. If PAPER OUT light is on, press to load paper to top of-form.

LF key: Press to advance paper one line.

TEAR OFF key: Press to advance continuous feed paper to the tear-off edge.

After tearing off paper, press any key to retract forms to top-of-form.

MODE key: With the printer offline, press to cycle between the LETTER/DRAFT,

FONT1/FONT2 and MENU1/MENU2 option pairs. An option pair is active when one

light is on and the other is flashing. On steadily indicates an option is selected;

flashing indicates an option is not selected. Press FF or LF key to select left-hand

or right-hand option, respectively. To return to normal mode, continue pressing

MODE key until no option pair lights are flashing. To return parameters to factory

default settings, hold MODE and LF keys while turning on printer. Continue holding

keys until printer beeps.

LOAD/UNLOAD key: Press to advance paper to top of form or to retract con-

tinuous feed paper to park position.

Self-test

Turn on printer while holding FF key. Continue holding FF key until printer beeps.

The firmware version, resident emulations and a continuous ASCII pattern is printed.

To pause self-test or hex dump, press MODE or LF key. To resume, press MODE

or LF key again. To terminate, press ONLINE key.

Hex dump

Turn on printer while holding FF and LF keys.

Printer Configuration

The printer is configured through the setup mode. Load continuous feed paper and

turn on printer while holding MODE key. Continue holding MODE key until the

printer beeps. Upon entering setup mode, the function menu and instructions for

using the setup mode are printed. Upon selecting a function that contains items and

options, that function's first item and its options are printed. Each function is summa-

rized below. *Denotes default settings.

SAVE&END - Select to save any changes made in setup mode and exit setup

mode. To exit setup mode without saving changes, turn printer off.

PANEL - Assigns a font and pitch to FONT1 and FONT2 and regular or high-

speed draft to DRAFT on control panel.

<DRAFT> - DRAFT *, HI-DRFT

<FONT1> - 1COUR 10 *, PRSTG12, COMPRSD, BOLDFCE, PICA 10,

CORRESP, [names from font card] DOWNLD0, DOWNLD1

<F1PITCH> - ## CPI (default 10 cpi), PROP SP

<FONT2> - (Same as FONT1 except default = PRSTG12)

<QUALITY> - LETTER *, REPORT, DRAFT, HI-DRAFT

<F2PITCH> - ## CPI (default 12 cpi), PROP SP

MENU1 and MENU2 - Assigns print features to MENU1 and MENU2 on control

panel. Items and options for MENU1 and MENU2 are identical.

<EMULATE, - DPL24C *, IBMXL24, LQ2500, LQ2550, names from emulation

card‘

<FONT> - COUR 10 *, PRSTG12, COMPRSD, BOLDFCE, PICA 10, CORRESP,

names from font card‘ DOWNLD0, DOWNLD1

<QUALITY> - LETTER *, REPORT, DRAFT, HI-DRFT

<PITCH> - # CPI (default 10 cpi), PROP SP

<LINE SP> - ## LPI (default 6 Ipi)3

<CHAR-W(idth)> - NORMAL, 2TIMES, 4TIMES (i)

<CHAR-H(eight)> - NORMAL, 2TIMES, 4TIMES (i)

<ATTRIB> - NONE, ITALICS (i), CONDNSD (i), SHADOW, BOLD

<PAGE LG> - ## IN (default 11 inches)

<COLOR> - AUTOSEL (software makes selection), BLACK, YELLOW, MAGENTA,

CYAN

<LFT-END> - ## COLM (specifies starting column of left margin, default 1)

<TOP-MRG> - ## LINE (specifies top margin, default 1)

<LANGUAGE> - USA *, UK, GERMAN, FRENCH, ITALIAN, SPANISH, SWEDISH,

FINNISH, DANISH1, DANISH2, PAGE### ISO8859 additional available for Epson

emulations‘

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujitsu DL3600 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info