Bedienungsanleitung Fujitsu fi 6010n (Seite 17 von 21) (Englisch)

213056

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Appendix D Network Connection Troubleshooting

■ Checking Basic Network Operation with a Ping Test

If a network connection is not possible, refer to "3.9 Checking the Network Connection" (page 11) for ping results and

how to deal with them.

OK: Connection is operating normally. NG: Connection is faulty.

Result

Connection

status

Server name

setting

Action

"Ping statistics" shows

"Lost=0 (0% loss)"

OK IP address / host

name / FQDN

None

"Ping statistics" shows

"Lost=4 (100% loss)"

NG IP address / host

name / FQDN

Check that the ping target IP address, host name, or

FQDN is correct.

IP Address If the ping target IP address is correct, refer to "Fail-

ure to Connect to a Server using its IP Address" (page

24) for further solutions.

Host name /

FQDN

On the "Network Status" screen, change [Link speed /

Duplex mode] from "Auto-Negotiation" to a fixed mode.

This can be changed as follows:

1. Select the [Network Settings] tab on the top menu.

2. Press the [ ] button on the left side menu.

3. Select the [Network Status] tab on the left side menu.

4. On the "Network Status" screen, select [Link Speed/

Duplex Mode].

5. Press the [OK] button.

"Ping statistics" shows

"Lost=N (1 to 99%

loss)"

NG IP address / host

name / FQDN

There may be a problem with the quality of the LAN

cable. Replace the LAN cable and try again.

IP address / host

name / FQDN

On the "Network Status" screen, change [Link speed /

Duplex mode] from "Auto-Negotiation" to a fixed mode.

This can be changed as follows:

1. Select the [Network Settings] tab on the top menu.

2. Press the [ ] button on the left side menu.

3. Select the [Network Status] tab on the left side menu.

4. On the "Network Status" screen, select [Link Speed/

Duplex Mode].

5. Press the [OK] button.

"Hardware error" NG IP address / host

name / FQDN

The LAN cable may have become disconnected dur-

ing the Ping test. Check the status of the LAN cable

and try again.

"Ping request could

not find host

xxxxxxxxx. Please

check the name and

try again."

NG Host name /

FQDN

Check that the ping target host name or FQDN is cor-

rect.

Check that the DNS server or WINS server settings

are correct.

If the ping target host name or FQDN is correct, refer

to "Failure to Connect to a Server using its Host

Name or FQDN" (page 25) for further solutions.

fi-6010N Network Scanner Getting Started

■ Failure to Connect to a Server using its IP Address

If a server cannot be connected to by using its IP address, and does not respond to a ping test, try the following steps:

No. Problem Action

1 Connection error between a server and the

scanner, or problem with the LAN cable.

Check that the LAN cable has been attached to both the scanner

and server correctly.

If the server is connected using a LAN cable (straight type), in

case auto-mdi (automatic selection) is not supported, a LAN

cable (crossover type), switch, or router is required between the

scanner and server.

If this is not the case, the LAN cable may be faulty. Find a

LAN cable that functions normally and try again.

2 IP address or subnet mask is invalid. On the "IP Address" screen, check that the IP address or subnet

mask settings are correct.

For more details about the "IP Address" screen, refer to "3.5

Setting the IP Address/DHCP" (page 8).

3 When using DHCP, the DHCP server does

not operate normally, or there is a problem

with the DHCP server settings.

Check the DHCP server connection status and the details of the

server settings.

If using DHCP, on the "Network Status" screen, check that IP

address, subnet mask, and default gateway settings are all cor-

rect.

If these settings are not correct, the DHCP server may not oper-

ate normally, or the DHCP server may not assign valid IP

addresses because of restricted number of leases or MAC

address validation.

If the DHCP server operating environment is changed, restart

the scanner.

The "Network Status" screen can be displayed as follows:

1. Select the [Network Settings] tab on the top menu.

2. Press the [ ] button on the left side menu.

3. Select the [Network Status] tab on the left side menu.

4 Another host or communication device is

connected using the same IP address as

the scanner.

If the same IP address has already been used by another host or

communication device, then even if the other device has been

given a different IP address the server may not recognize the

scanner’s "duplicate" IP address until it is rebooted. Restart the

server.

If a duplicate IP address connection from another host or com-

munication device exists on a LAN, both it will be unusable.

If a duplicate IP address connection from another host or com-

munication device exists, pull out its LAN cable and restart the

server.

5 Access is denied due to the establishment

of a firewall between the server and the

scanner.

If a firewall has been established between the server and the

scanner, check that it has not been set to deny access to the net-

work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujitsu fi 6010n Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fujitsu fi 6010n

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info