Bedienungsanleitung Fusion MS-FR702 (Seite 5 von 6) (Englisch)

522168

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Installation Guide

1. Check clearance around the mounting area before installation, ensuring the area is

free from obstruction, and there is adequate depth for the speaker.

2. Check that the area chosen for mounting the speaker is ﬂat. If the area is curved, it

may not be possible to ﬁt the speaker without “twisting” the frame.

3. If the installation area is only slightly curved, use the extra thick closed cell foam

gasket provided.

4. Using the supplied mounting template, mark the correct diameter on the mounting

surface.

5. Use a suitable cutting tool to remove the marked surface, and drill four holes for the

screws to pass through.

(NOTE: Conﬁrm you are happy with badge position relative to mounting holes)

6. Connect the wires before mounting the speaker. Be sure to observe the correct

polarity.

7. With the grille removed, mount the speaker using the four stainless steel screws, and

the stainless retainer clips supplied. DO NOT over tighten the screws, especially if the

mounting area is not ﬂat.

8. Twist the grille into position.

Installation Tips

Any speaker will only perform to its best capabilities, when correctly placed in the

listening area. FUSION Engineers recognise that unlike a home or motor vehicle installation,

there are an extremely wide range of marine environments where speakers may be

placed. FUSION Full Range Marine Speakers are optimised to perform in the widest possible

range of mounting locations, but a little thought and care with placement will always be

rewarded with better sound.

• Highfrequenciesaredirectional.Placingthespeakerslowdownintheboatwilllose

some of this information. (To improve dispersion of the high frequencies, the grille on

your FUSION Full Range Speaker has a uniquely designed “phase correction” feature in

the centre, for best performance with the grille on.)

• Speakersshouldbeplacedtosimulatea“soundstage”,bybeingplacedwhereyouare

able to hear both speakers in a stereo situation.

• Bassisdependantontheareabehindthespeaker.Toosmallanareawillrestrictbass,

too large will compromise bass performance.

• Placingaspeakersuchthatitisveryclosetoanopenarea(wheresoundfromthe

back of the loudspeaker has a very short path to compete with sound from the front

of the loudspeaker) produces the least bass.

• Ifpossible,tryandmaketheareabehindaspeakeranenclosure.

Where the speaker is directly exposed to the outside environment, it is best if this is

a sealed enclosure. (Especially if the loudspeaker is exposed to “wash down”, as a vent

might allow water to collect in the enclosure.)

Where the speaker is not so exposed (an inside cabin for instance), a better bass

performance can be had if the enclosure is a ported or vented type. To help you achieve

the best possible result see the optimum enclosure design recommendations. These are

by volume only, and for the ported option, an optimum vent size/length is given.

008

Installation Guide

009

Installation Tips

Grille, Twist

Into Position

Stainless

Screws

Speaker

Mounting

Gasket

Mounting

Surface

www.busse-yachtshop.de | info@busse-yachtshop.de

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fusion MS-FR702 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info