Bedienungsanleitung Futaba 6EXAP (Seite 22 von 24) (Englisch)

28983

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

FLIGHT PREPARATION

Flight preparation is to be done at the flying field.

IMPORTANT:

Your radio control system transmits a signal on a certain frequency. Be certain you know what the

frequency is. This is expressed as a two-digit number (42, 56, etc.), and can be found on the container the transmitter

came in and is also located on the transmitter and receiver. There are several different frequencies, but there is still a

chance that someone else at the flying field may be on the same frequency as you. Two models can never be operated at

the same time on the same frequency-no matter what the modulation (AM, FM, PCM). If you turn on your transmitter while

another person is flying on the same frequency, a crash will result. NEVER

NEVER

turn on your transmitter until you have

permission from your instructor, and until you have possession of the frequency clip used for frequency control at the

flying site.

If you are an inexperienced pilot, be certain your flight instructor performs these following checks with you.

Check the controls

1. Get the frequency clip from the frequency control board at your flying site.

2. Mount the wing to the fuselage. Turn on the transmitter, then the receiver (remember to do this in reverse order when

turning off the system). Be certain the correct model memory matching the model you will be flying is the one on the LCD

screen.

3. Operate and observe the controls. Look for inadvertent movement and listen for abnormal servo sounds. If problems are

noted, correct them before flying. Look for binding pushrods or servo arms or pushrods that interfere with each other.

4. One at a time, operate each control on the airplane using the sticks on the transmitter to make certain each control is

responding correctly. This must

must

be done before every

every

flight. (There are several types of malfunctions that can be discovered

by performing this elementary task, thus saving your model!)

Range check the radio

A range check must

must

be performed before the first

first

flight of a new model. It is not necessary to do a range check before every

flight (but is not a bad idea to perform a range check before the first flight of each day). A range check is the final opportunity

to reveal any radio malfunctions, and to be certain the system has adequate operational range.

1.Turn on the transmitter, then the receiver. Leave the transmitter antenna all the way down. Walk away from the model while

simultaneously operating the controls. Have an assistant stand by the model and signal what the controls are doing to confirm

that they operate correctly. You should be able to walk approximately 20 - 30 paces from the model without losing control or

seeing

“jitter” in the servos.

2.If everything operates correctly, return to the model. Set the transmitter in a safe, yet accessible location so it will be within

reach after starting the engine. Be certain the throttle stick is all the way down,

down,

then start the engine. Perform another range

check with your assistant holding the plane and the engine running at various speeds. If the servos jitter or move

inadvertently, there may be a problem. Do not fly

Do not fly

the plane! Look for loose servo connections or binding pushrods. Also be

certain you are the only one on your frequency, and that the battery has been fully charged.

3.When ready to fly, remember to fully extend the transmitter antenna. Avoid pointing the antenna directly at the model as the

signal is weakest in that direction.

Do not fly in the rain!

Moisture may enter the transmitter through the antenna or stick openings and cause erratic operation or loss of control. If you

must fly in wet weather during a contest, be sure to cover the transmitter with a plastic bag or other waterproof cover.

MODEL DATA RECORDING SHEET

After finalizing the programming for each model, fill out the values and settings in the Model Data Recording Sheets

Model Data Recording Sheets

in the

back of the manual. The data sheets will serve as a backup in case a program is ever lost or inadvertently reset, or in case

you have to intentionally reset a program to make room for another model. Make additional copies before filling out the

sheets.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6EXAP Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info