Bedienungsanleitung Futaba R3001SB (Seite 2 von 2) (Englisch)

747950

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2017, 1 (1)

WARNING

Do not insert or remove the S.BUS connector while

the receiver power is ON.

Since the S.BUS servo switches the operation mode automatically

according to the type of signal (S.BUS signal/PWM signal) from the re-

ceiver, if the connector is inserted or removed while the power is ON, an

S.BUS connected servo will be erroneously recognized and may stop.

WARNING

Turn on the power on transmitter → receiver in order.

In addition, always check the operation of all the func-

tions before ﬂight.

What is S.BUS?

Different from conventional radio control systems, the S.BUS

system uses data communication to transmit control signals

from a receiver to a servo, gyro, or other S.BUS compatible

devices. This data includes commands such as “move the

channel 3 servo to 15 degrees, move the channel 5 servo to

30 degrees” to multiple devices. The S.BUSGHYLFHVH[HFXWH

only those commands for their own set channel. For this

reason, it can be used by connecting multiple servos to the

same signal line.

/LQNWRWKHWUDQVPLWWHU

Easy Link ID allows T-FHSS Air receivers to link to

compatible transmitter without pressing the link button on the

receiver.

Bring the transmitter and the receiver close to each

other, within 20 inches (half meter).

Turn on the transmitter. Place the transmitter into the

receiver linking mode.

Turn on the receiver.

The receiver will wait for the linking process to begin

for 3 seconds. Following that it will return to the

normal operation mode.

When the LED of the receiver changes from blinking

red to solid green, linking is completed.

(A link waiting state is ended in 3 second.)

* Refer to the transmitters operation manual for complete details on how

to place the transmitter into the linking mode.

WARNING

Do not perform the linking procedure while the mo-

tor's main wire connected or the engine is operating as it

may result in serious injury.

When the linking is complete, please cycle the receiv-

er power and ensure the receiver is properly linked to the

transmitter.

Please power up your system in this order. Transmit-

ter ﬁrst, followed by the receiver.

If the R3001SB receiver was previously linked to an-

other transmitter, make sure that transmitter is not oper-

ating while linking the receiver to the new transmitter.

* If there are many T-FHSS Air systems turned on in close proximity,

your receiver might have difﬁculty establishing a link to your transmit-

ter. This is a rare occurrence. However, should another T-FHSS Air

transmitter/receiver be linking at the same time, your receiver could

link to the wrong transmitter. This is very dangerous if you do not no-

tice this situation. In order to avoid the problem,we strongly recom-

mend you to double check whether your receiver is really under con-

trol by your transmitter.

* If the System Type of the transmitter is changed, the receiver will need

to be re-linked to the transmitter.

* Link is required when a new model is made from a model selection.

&KDQQHO0RGHV6%86

⇔

CH3)

The R3001SB is capable of changing its channel allocations

as described in the table below.

Turn on the receiver. (At this moment, the transmitter

should be off.) Then, LED blinks RED in about 3

seconds. Next, wait until it becomes solid RED.

Press and hold the Mode switch more than 5

seconds.

Release the button when the LED blinks RED and

GREEN simultaneously.

The receiver is now in the "Operation CH Set" mode.

At this moment, the LED indicates current set sta-

tus through ﬂashing a pattern that corresponds to the

CH mode.

&DQQRWH[LWWKLV&+VHWWLQJPRGHEHIRUHWKHRSHUDWLRQPRGHLV

¿[HG

6HHWKHQH[WWDEOHWKDWVKRZVFRUUHVSRQGHQFHEHWZHHQ&+PRGH

DQGZD\RIÀDVKLQJ/('

'HIDXOW&+PRGHLV0RGH%

By pressing the Mode switch, the operation CH is

switched sequentially as " Mode B" "Mode A" "Mode

B"....

Mode A Mode B

3/S.BUS 3CH S.BUS

Red LED blink 1 time 2 time

R3001SB CH Mode table

Default CH mode

The operation mode will be set by pressing the Mode

switch more than 2 seconds at the desired CH

mode.

Release the button when the LED blinks RED and

GREEN simultaneously. Then, the operation CH is

ﬁxed.

After confirming the operation CH mode is changed,

turn off and back on the receiver power.

*The “Operation CH Set” mode cannot be changed during the

receiver communicates to the transmitter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R3001SB Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info