Bedienungsanleitung Futaba R324SBS (Seite 1 von 1) (Englisch)

747969

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Link Procedure

Each transmitter has an individually assigned, unique ID code. In order to start

operation, the receiver must be linked with the ID code of the transmitter with

which it is being paired. Once the link is made, the ID code is stored in the

receiver and no further linking is necessary unless the receiver is to be used with

another transmitter.

Place the transmitter and the receiver close to each other within

half (0.5) meter.

Place the transmitter into the linking mode, and turn on the

receiver.

During countdown, push the receiver tact switch for

approximately 2 seconds. The LED will begin to blink red. After

the receiver LED switches from blinking red to green

→

green

(red) steady light, If the transmitter and receiver are linked

normally, set the power switch to the OFF position and then

return it to the PWR ON position. If the receiver LED lights

green, linking was successful. (T4PLS,T4GRS : set the power

switch to the OFF position and then return it to the PWR ON

position.) Actually check servo operation.

* Please refer to the table below for LED status and receiver condition.

* Refer to the transmitters operation manual for complete details on how to place the transmitter

into the linking mode.

* If there are many T-FHSS systems turned on in close proximity, your receiver might have

difﬁculty establishing a link to your transmitter. This is a rare occurrence. However, should

another T-FHSS transmitter/receiver be linking at the same time, your receiver could link to the

wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid

the problem,we strongly recommend you to double check whether your receiver is really under

control by your transmitter.

WARNING

After the linking is done, please cycle receiver power and check if the

receiver to be linked is really under the control by the transmitter to be linked.

Do not perform the linking procedure with motor's main wire connected

or with the engine operating as it may result in serious injury.

Operating Precautions:

Once the

R324SBS

detects the

T-FHSS

normal

mode

T-FHSS high speed mode

, the detected

mode is locked as long as the power is ON.

When need to change the mode, please

cycle power.

Note: The R324SBS is compatible with the T-FHSS system transmitters.

The receiver type setting of the transmitter is set in T-FHSS.

*Futaba T-FHSS system does not work with current Futaba S-FHSS/FHSS/FASSTest/FASST /T-FHSS Air system.

Usage condition on "High Speed mode"

CAUTION

When using the high-speed mode, use a Futaba digital servo

(including brushless servo). Analog servos cannot be used.

• The use of analog servos may cause servo trouble.

1M23N17492

T-FHSS-2.4GHz System

Diversity antenna

S.BUS2, 4-Channel Receiver for Model Car

Thank you for purchasing the

R324SBS

receiver. The

R324SBS

is designed for use

with the Futaba

T-FHSS

system transmitter.

The

R324SBS

receiver has adopted the newly

developed bidirectional communication

system "

T-FHSS

• Telemetry system

With the

telemetry system

, the running status can be displayed at the transmitter. The telemetry data can be checked at the

transmitter by connecting the

telemetry sensor

sold separately to the

S.BUS2

connector of the

R324SBS

receiver.

• Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos,

including BLS series, and most peripheral equipments such as the brushless ESCs. Please pay special attention to the information

contained within this manual and transmitter's manual in order to have a pleasant running experience.

• Diversity antenna equipment

R324SBS

WARNING

NEVER use dry batteries for the power supply of the R324SBS as

this may cause difﬁculties with the receiver's operation.

Wrap the receiver with something soft, such as foam rubber, to avoid

vibration. Do not splash water over the receiver.

Since the receiver generates a certain amount of heat, install the

place with good ventilation.

Do not put any conductive equipment/sticker on the antenna part.

(Receiver top)

• Otherwise, the operating range may become shorter.

No signal reception LED: Red

Receiving signals LED: Green

Unrecoverable fail-

ure (EEPROM,etc.)

LED: Red and

Green turn on

alternately

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2017, 2 (1)

R324SBS Speciﬁcations:

(

T-FHSS

system,

S.BUS2

, 4-channel receiver)

• Receiving on 2.4GHz band

• System:

T-FHSS

system

At Normal/High speed mode (auto detection)

•

Power requirement Operating voltage: 3.7V-7.4V

• F/S and Battery F/S function:It is set according to the transmitter used.

• Battery F/S voltage: Set it with the transmitter arbitrarily.

• Size: 1.38x0.91x0.49” (35.1x23.2x12.5mm)

• Weight: 0.29oz. (8.3g)

+8%

%DWWHU\

6WHHULQJVHUYR

7KURWWOHVHUYR

Collect many telemetry

sensors by HUB and connect

them to S.BUS2 port.

,WFRQQHFWVZLWKSRUWZKLFKLVQRWXVHGك

:KHQDOOWKHSRUWVDUHXVHGFRQQHFW

DEDWWHU\XVLQJ+8%RU<KDUQHVV

%XLOWLQDQWHQQD

5HFHLYHUWRSLVFOHDQ

2XWVLGH$QWHQQD

/LQN6ZLWFK岜

&+

&+

6%86

&+

/('

7HPSHUDWXUH

VHQVRU

530VHQVRU

9ROWDJHVHQVRU

7HOHPHWU\VHQVRUV

2SWLRQ

'RQWFXWRUEXQGOH

WKHUHFHLYHU

DQWHQQDZLUH

The Example of Connection

LED Indication

Compliance Information Statement (for U.S.A.)

This device, trade name Futaba Corporation, model number R324SBS, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

To assure continued FCC compliance:

$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOGYRLGWKHXVHUVDXWKRULW\

to operate the equipment.

2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

Futaba R324SBS Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info