Bedienungsanleitung Futaba R7006SB (Seite 1 von 2) (Englisch)

747959

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

R7006SB

90˚

1M23N31002

LED Indication

56%

6%863RUW6%

6%863RUW6%

&KDQQHO



6%86VHUYRV

6%86*\URV

7KHUHFHLYHUSRZHUVXSSO\FDQ

EHFRQQHFWHGWRDQ\SRUW

+XE

6%86HTXLSPHQW

7HOHPHWU\VHQVRU

6HUYRIRU FRQYHQWLRQDO

V\VWHP

%DWWHU\

 ع 9

6ZLWFK

6HUYR

<KDUQHVV

:KHQDOOSRUWVDUHXVHG

System Mode LED Status Link LED

FASSTest Green Solid

No signal reception Red Solid

Receiving signals Green Solid

Waiting for link

Start → 2second

later → Red Blink

（1second）

FASST Oﬀ

No signal reception Red Solid

Receiving signals Green Solid

Receiving signals but ID is

unmatched

Green Blink

Waiting for link Red Blink

FASSTest

FASST

- Unrecoverable error (EEPROM, etc.) Alternate blink

/LQN/('

0RGH/('

/LQN0RGH

VZLWFK

●

Applicable systems: Futaba FASSTest-2.4GHz / FASST (Multi-ch,7ch) -2.4GHz system transmitter

◆

FASSTest-2.4GHz Bidirectional Communication System / FASST(Multi-ch,7ch) -2.4GHz

◆

S.BUS2 / S.BUS Port and 6 Channels for Conventional System Receiver

Usage precaution

• Analog servos cannot be used with the R7006SB in the FASSTest

12CH / FASST High-speed mode.

WARNING

Changes or modification not approved by the party responsible for

compliance could void the users authority to operate the equipment.

The R7006SB receiver should be protected from vibration by foam

rubber, Velcro, or similar mounting methods. Protect from moisture.

Keep away from conductive materials to avoid short circuits.

Antenna installation precaution

Do not cut or bundle the receiver antenna wire.

Do not bend the coaxial cable. It causes damage.

The antennas must be mounted in such a way to assure they are strain

relieved.

Keep the antenna as far away from the motor, ESC and other noise

sources as you possibly can.

Do not touch the antenna to metal, carbon, or other conductive material.

Be sure that the two antennas are placed at 90 degrees to each other.

■ The R7006SB has two antennas. In order to maximize signal reception

and promote safe modeling Futaba has adopted a diversity antenna system.

This allows the receiver to obtain RF signals on both antennas and fly

problem-free.

Antenna installation for carbon fuselage

You must leave 30mm at the tip of the antenna fully exposed. The

exposed antenna should be secured so that it cannot move around or

back inside of your aircraft.

Be careful of connector insertion

Don't connect an S.BUS servo / gyro to S.BUS2 connector.

Link precaution

Do not perform the linking procedure while the motor's main power is

connected or the engine is operating as it may result in serious injury.

When the linking is complete, please cycle the receiver power and

ensure the receiver is properly linked to the transmitter.

Please power up your system in this order: Transmitter ﬁrst, followed

by the receiver.

If the R7006SB receiver was previously linked to another transmitter,

make sure that transmitter is not operating while linking the receiver to

the new transmitter.

Thank you for purchasing a Futaba R7006SB FASSTest-2.4GHz compatible receiver.

The R7006SB receiver features bi-directional communication

with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also

includes both standard PWM output ports (1-6ch) and S.BUS output ports. The R7006SB can also be switched to the FASST(Multi-ch/7-ch) System.

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation, model

number R7006SB, complies with part 15 of the

FCC Rules. Operation is subject to the following

three conditions:

(1) This device may not cause harmful interference,

and

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

(3) This module meets the requirements for a

mobile device that may be used at separation

distances of more than 20cm from human body.

To meet the RF exposure requirements of the FCC

this device shall not be co-located with another

transmitting device.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL

61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.

com (Support)

Antenna

installation

R7006SB Speciﬁcations

FASSTest-2.4GHz system(18ch/12ch mode)

FASST-2.4GHz system (Multi-ch/7ch mode)

S.BUS2 and S.BUS port and 6ch for conventional system receiver

• Dual antenna diversity

• Size: 0.89 x 1.5 x 0.48 in. (22.5x38.3x12.2mm)

• Weight: 0.3 oz. (8.5g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)

• Battery F/S Voltage: FASSTest---It sets up with a transmitter

FASST---3.8V

*When on "FASST-7ch" mode, the fail safe function can be set for 3-channel only.

*Be sure that when using ESCs regulated output the capacity of the ESC must meet your us-

age condition.

1HYHUXVHGU\EDWWHULHVIRUWKHSRZHUVXSSO\RIWKH56%DVWKH\PD\FDXVHGLI¿FXOWLHV

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R7006SB Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba R7006SB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info