Bedienungsanleitung Futaba R7018SB (Seite 4 von 5) (Englisch)

747962

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Link to the transmitter : FASST

Bring the transmitter and the receiver close to each

other, within 20 inches (half meter).

Turn on the transmitter and receiver.

Link operation is performed by the Link/Mode switch.

• When using TM-8 module, it's possible to set F/S position (only 3CH).

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold time

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

Besides TM-8

Re-link(ID set)

Refer to the instruction manual of the transmitter or module used

for a description of the linking operation, F/S position setting

methods and other details.

When using Multi prop (MPDX-1)

The MPDX-1 can be used with FASSTest by merely

setting the corresponding transmitter. (Refer to the

instruction manual of the corresponding transmitter.)

When using the MPDX-1 Multi Prop Decoder (sold

separately) with the FASST system, change the setting by

the following method.

Enable the MPDX-1 at channels 11 and 12. (Initial value:

OFF)

Channels 11 and 12 cannot be used individually for

MPDX-1 output.

The MPDX-1 extends 1 channel to 8 channels. However,

since the response speed becomes slower and there are

functional restrictions, use it at simple switch operation

and other applications that require numerous channels.

Multi prop mode Change method

. Switch the receiver to the FASST system (Normal or

High-speed).

. Turn on the receiver power. (Transmitter power off)

. Press the Link/Mode switch for at least 10 seconds.

. When the LED blinks red and changes to red/green

simultaneous rapid blinking, release the switch.

. The receiver enters the multi prop mode and the LED of

the current mode blinks. (Initial value: OFF)

. Each time the switch is pressed, the mode changes.

. When the receiver was switched to the desired mode,

press the Link/Mode switch for at least 2 seconds.

. When the LED switches to red/green simultaneous

rapid blinking, mode switching is complete. Release the

switch.

. When switching is complete, turn on the power. When

the power is turned on, the receiver switches to the new

mode.

FASST

When switched, the R7018SB can use the FASST-Multi-ch mode. When the FASST system is used, the telemetry and

Extra Voltage ports cannot be used. The FASST system has a Normal mode and a High-speed mode. However, in the

High-speed mode, analog servos cannot be used at CH1

∼

Green LED blink Mode

1 time

Multi prop mode OFF

2 time

Multi prop mode ON

FASSTest

FASST

When a telemetry adapter (TMA-1) is used

: FASSTest only

When using a TMA-1 (sold separately), change the

settings by the following method.

The TMA-1 is a device for viewing the telemetry data on

a smartphone or tablet.

R7018SB and TMA-1 linking method

. Switch the receiver to FASSTest system.

. Link the transmitter and receiver, and after conﬁrming

operation, turn off the power.

. Turn on the receiver power. (Transmitter power off)

. Press the Link/Mode switch for at least 10 seconds.

. After the LED blinks red and changes to red/green

simultaneous rapid blinking, release the switch.

. The receiver enters the linked with TMA-1 mode, and

the LED begins red/green simultaneous rapid blinking.

. Press the TMA-1 link switch until the LED starts to blink

and wait for the TMA-1 to link.

. When TMA-1 linking is complete, the TMA-1 LED

changes from red to green for a moment.

. When linking is complete, turn on the receiver power

and check the operation of all the devices.

03';ق2SWLRQك

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

R7018SB Speciﬁcations

FASSTest-2.4GHz system(18CH/12CH mode)FASST-2.4GHz system

(Multi-ch mode)

S.BUS2 and S.BUS port and Linear 16 ch +Digital 2 ch for conventional

system receiver

• Dual antenna diversity

• Size: 2.15 x 1.59 x 0.64 in. (54.6x40.4x16.3mm)

• Weight: 1.48 oz. (42g)

• Power requirement: 6.0V to 7.4V(Voltage range: 4.8 to 8.4V)

• Battery F/S Voltage: It sets up with a transmitter (F/S can't be used in

case of FASST.)

• Extra Voltage port: 0

∼

70V DC

- 4 -

All product and company names mentioned

herein are the trademarks or registered

trademarks of their respective owners.

本產品符合低功率電波輻射性電機管理辦法第十二條、第十四條等條文規定

1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加

大功率或變更原設計之特性及功能。

2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，

並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率

射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R7018SB Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba R7018SB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info