Bedienungsanleitung Fysic FKW-2500 (Seite 23 von 28) (Deutsch, Englisch, Holländisch, Französisch)

678952

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

DAILY SNOOZE AND ALARM CLOCK FUNCTION:

The weather station oers 4 alarm clock functions. The alarm clock is activated when the alarm

clock functions with a number appears in the display. The alarm clock function will start ashing

while the snooze function is enabled. Every 5 minutes an alarm signal will sound.

To set the wake-up time:

• Repeatedly press the “ALARM”(21) button to select the wake-up time. Choose

from wake-up time 1 through 4. Each wake-up time may be set individually.

• Go to the desired wake-up time (icon 1, 2, 3 or 4 and AL is visible).

• Press and hold the “ALARM” button for 2 seconds until the wake-up time hours

start ashing. Press the ▲(23) and ▼(16) buttons to set the desired hour.

• Press the “ALARM” button again; the wake-up time minutes start ashing. Press the ▲(23)

and ▼(16) buttons to set the desired minutes.

• Press the “ALARM” button again or wait 10 seconds to save your settings.

• Use the “AL 1-2” (23) button to select the desired wake-up time 1 and 2, use the “AL 3-4”

(16) button to select the desired wake-up time 3 and 4. This wake-up time is active when

the icon appears in the display. All 4 wake-up times or a combination of them may be se-

lected.

Wake-up time repetition:

Use the selection button 19 to set the wake-up time repetition to business

days Monday through Friday (MON - FRI) or to the entire week (MON -

SUN).

To disable the alarm signal:

As soon as an active wake-up time is reached, the weather station will sound an alarm signal.

Press any button (except the “SNOOZE” button) to stop the alarm signal. If no button is

pressed, the alarm signal will stop automatically after ± 2 minutes.

After 24 hours the alarm signal, connected to the set wake-up time, will sound again.

Snooze function:

During an alarm, press the “SNOOZE” (17) button to temporarily stop the alarm signal and

enter the snooze mode; the icon starts ashing. Upon activating the snooze mode, the alarm

signal will sound again after 5 minutes. This may be repeated for up to 7 times.

To cancel the snooze function during snoozing:

While snoozing, press the “ALERT” (20) button to cancel the snooze function.

The icon disappears.

THERMOMETER:

The temperature is shown at the left side in the display. Provided that the

outdoor sensor is registered, the outdoor temperature is shown at the right

side in the display. See “To manually set the weather station” to have the

temperature display shown in °C or °F.

When the measured temperature is outside the eective measuring range,

the display will show LL.L for values that are too low and HH.H for values that

are too high.

Temperature alert function:

You may only set an alert for the outdoor temperature.

You may set the desired temperature and as soon as the outdoor temperature exceeds the

set temperature an alert will sound. You may also set a lower limit for an alert as soon as the

outdoor temperature falls below the set temperature. Both thresholds can be enabled simultane-

ously.

D S T

AA 1,5V

ALARM MODE

MON - FRI

MON - SUN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fysic FKW-2500 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info