Bedienungsanleitung Gaggia Brera (Seite 11 von 26) (Englisch)

480804

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

• 31 •

English

At this point the button “ “ is program-

med; each time it is pressed and released,

the machine will brew the same amount

of co ee that was just programmed.

The same operation can be repeated for

the “

“ button. If the “ “ or “ “

button is pressed twice to brew coffee,

the machine will brew double the stored

quantity.

Standby

The machine is designed for energy sa-

ving. The machine automatically turns o

after 60 minutes of inactivity.

The “

“ button blinks when the machine

is in stand-by mode.

Note: During the turning o

phase, the machine performs

a rinse cycle, if a co ee product has

been brewed.

Warning: When turning the machine

on after it has been turned com-

pletely off, the machine will be in

stand-by mode

To turn the machine on again simply press

the STAND-BY button (if the power but-

ton is set to “I”). In this case the machine

will go through the rinse cycle only if the

boiler is cold.

Dispensing Spout

Adjustment

Most cups on the market can be used with

this co ee machine.

The height of the dispensing spout may

be adjusted to better  t the dimensions

of the cups that you wish to use.

Manually move the dispensing spout up

or down to adjust its height by placing

your  ngers as shown in the  gure.

The recommended positions are:

For use with small cups;

The machine allows slight adjustments to

the co ee grinder to adapt it to the kind

of co ee used.

To make any adjustment, press and turn

the knob inside the co ee bean hopper.

Press and turn the knob by one notch at

a time and brew 2-3 cups of coffee; this

is the only way to notice differences in

grind.

The reference marks inside the coffee

bean hopper indicate the grind setting.

There are 5 di erent grind settings to cho-

ose from with the following references:

Large Mark - Coarse Grind

Small Mark - Fine Grind.

Adjusting the Coﬀ ee Length

The machine allows you to adjust the

amount of brewed coffee according to

your taste and/or the size of your cups.

Each time the “ “

or “ “ buttons are

pressed and released, the machine brews

a pre-set amount of co ee, as per factory

settings. This amount may be reprogram-

med to your taste. Each button may be

individually programmed for a specific

brew setting.

As an example, the following procedure

describes the programming of the button

“

“, which is normally associated with

espresso co ee.

• Place a cup under the dispensing

spout.

•

Hold the “ “ button pressed for 5

seconds to enter the programming

mode; the “

“ icon will blink quickly

and the co ee will start to be brewed;

the icon will flash during the whole

co ee brewing cycle.

• Press the “ “ button again when the

amount of coffee in the cup reaches

the desired level.

Blinking

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggia Brera Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggia Brera

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info