Bedienungsanleitung Gardenline WLBCF310 (Seite 40 von 42) (Englisch)

724674

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Understanding and using these operating instructions

31cc Brushcutter / Line Trimmer

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. WLBCF310 • 08/2015 • 49290

(toll free)

Operating instructions and safety notes!

AFTER SALES SUPPORT

(toll free)

31cc Brushcutter / Line Trimmer

e-mail: help@powertoolsupport.com1800 909 909

MODEL: №. WLBCF310 • 08/2015 • 49290

Troubleshooting

Problem

Possible Cause Solution

Power loss or

sudden stopping

of the engine

Fuel Tank (6) is empty

The mixture does not reach the

carburettor.

There is water in the mixture.

The air filter (3) is dirty.

There are carbon deposits in the cylinder

exhaust pipe or the muffler.

Flooded engine.

Check whether the fuel tank (6) is empty

and refuel if required.

NOTE: If the trimmer is being used a lot on

its side, the tank may require a minimum of

1/4 tank of fuel.

Clean the fuel ﬁlter in the fuel tank (6).

Drain and rinse the fuel system.

Reﬁll the fuel tank (6) with new

uncontaminated fuel.

Clean the air ﬁlter (3).

Clean or change the muﬄer.

Take the product to a Service Agent.

Move the choke to the run or Hot start

position and restart the unit.

Bad quality cut from

the line trimmer

Overloaded cutting due to too high

grass or too thick for engine power.

Wrapped vegetal material on the

cutting tool.

Line will not advance.

Line welded to itself.

Not enough line on the spool.

Line worn too short.

Line tangled on spool.

Cut tall grass from the top down.

Clean the material from the spool and line.

Manually advance the lines.

Open the spool and line assembly (35) and

ensure the lines have not crossed or tangled.

NOTE: Always ensure the engine is turned

oﬀ before undertaking this task.

Lubricate with silicone spray.

Manually advance the lines.

NOTE: Always ensure the engine is turned

oﬀ before undertaking this task.

Install more line.

NOTE: Always ensure the engine is turned

oﬀ before undertaking

this task.

Pull lines while alternately pressing down

on and releasing bump knob (34).

Remove line from the spool and rewind.

Engine does not

reach full speed

Check the fuel.

Check oil reservoir (24) level.

Check spark plug (1).

Use fresh fuel. Do not use ethanol based fuel.

Top up the oil if it is low.

Clean or replace if dirty or worn.

3T Brushcutter

Blade (28) rotates

at idle speed.

The Blade is not securely fitted.

The blade only rotates on run down of

the motor. i.e 5 seconds.

At idle the 3T brushcutter blade (28) is

rotating under power from the motor.

Ensure the blade nut is tightened (26)

This is normal but should not continue to

rotate under power from the motor at idle.

Immediately turn oﬀ the motor and take

the product to an authorized

Service Agent.

DO NOT continue to use the product.

For other issues not covered in this chart, please call Customer Service on 1800 909 909.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline WLBCF310 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info