Bedienungsanleitung Garmin Catalyst (Seite 5 von 18) (Englisch)

740416

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Getting Started

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

This device is only intended for recreational use in a circuit

environment. Never use this device on public roadways. Failure

to follow this warning may result in an accident causing property

damage, serious personal injury, or death. You are responsible

for using this device in a safe and prudent manner.

The first time you turn on your device, it guides you through the

initial setup steps with on-screen prompts. You should complete

these steps before using the device for the first time.

Turn on the device, and follow the on-screen instructions.

Update your device software (Updating Software Using a

‑

Fi Network, page 8).

Installation

Installing the Magnetic Mount in Your

Vehicle

WARNING

This product contains a lithium-ion battery. To prevent the

possibility of personal injury or product damage caused by

battery exposure to extreme heat, store the device out of direct

sunlight.

Both the device and its mount contain magnets. Under certain

circumstances, magnets may cause interference with some

internal medical devices and electronic devices, including

pacemakers, insulin pumps, or hard drives in laptop computers.

Keep the device away from medical devices and electronic

devices.

Clean and dry your windshield and the suction cup with a lint-

free cloth.

Press the suction cup to the windshield, and flip the lever .

Connect the ball of the suction cup mount and the ball of

the powered magnetic mount to the double-socket arms

Connect the double-ball link to both double-socket arms.

Tighten the knobs on both double-socket arms slightly.

If necessary, rotate the powered magnetic mount so the

Garmin

logo faces right-side up, and adjust the mount for

better viewing and operation.

Tighten the knobs to secure the mount.

Connecting the Mount to Vehicle Power

Plug the mini-USB end of the power cable into the mini-

USB port on the powered mount.

Plug the power cable into the included vehicle power adapter

Plug the vehicle power adapter into the power outlet in your

vehicle.

If necessary, turn on the vehicle ignition switch to provide

power to the power outlet in your vehicle.

Bare Wire USB Cable

WARNING

Garmin strongly recommends having an experienced installer

with the proper knowledge of electrical systems install the

device. Incorrectly wiring the power cable can result in damage

to the vehicle or the battery and can cause bodily injury.

The device includes a bare wire power adapter for use in

vehicles that are not equipped with a CLA power outlet. You can

also use this cable in applications where a hardwired permanent

power source is preferred. The device must be mounted in a

suitable and secure location in your vehicle, based on available

power sources and safe cable routing.

Device mini-USB connector

10 to 30 Vdc system input power (red)

System ground (black)

Camera Mounting Considerations

The first time you turn on your device, it provides information to

help you mount the camera. The camera affixes to the

windshield using the included adhesive mount. The adhesive

mount is difficult to remove after it is installed. You should

carefully consider the mounting location before you install the

mount.

• Do not mount the camera in a location that interferes with the

driver's view of the road.

• You should choose a mounting location that provides the

camera a clear view of the road ahead.

• You should choose a mounting location that is as high as

possible on the center of the windshield.

• You should verify the area of the windshield in front of the

camera is cleared by the windshield wipers.

• You should avoid placing the camera behind a tinted area of

the windshield.

Installing the Polarizing Filter on the Camera

The camera comes with a polarizing filter pre-installed over the

lens to help reduce glare from your windshield. If you remove

the polarizing filter, you can re-install it.

NOTICE

Do not rotate the lens cover while it is installed on the camera.

Position the filter so the line on the outer rim is facing up.

Getting Started 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Catalyst Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Catalyst

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info