Bedienungsanleitung Garmin Echo 100 (Seite 2 von 6) (Englisch)

463800

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

2 echoInstallationInstructions



Notice

Do not cut the transducer cable. Cutting the transducer cable will void your

warranty.

1. Position the transducer mount

➊

at the selected mounting location on the

transom (page 1).

➋

➊

➌

➍

➎

➏

2. Align the transducer parallel with the water line

➋

, and mark the center

location of each hole on the transducer mount.

3. Using a

in. (4 mm) bit, drill the pilot holes approximately 1 in.

(25 mm) deep at the marked locations, while taking the following

precautions.

• To avoid drilling the holes too deep, wrap a piece of tape around the

bit at 1 in. (25 mm) from the point of the bit to act as a guide.

• If you are installing the bracket on berglass, place a piece of tape

over the pilot-hole location to reduce cracking of the gel-coat.

4. Apply marine sealant to the included 30 mm M5 screws, and loosely

attach the transducer assembly to the transom.

5. Adjust the transducer assembly so that it extends beyond the bottom of

the transom

➌

approximately

in. (3 mm) on berglass hulls or

in.

(10 mm) on aluminum hulls

6. Make sure that the transducer is aligned parallel with the water line.

7. Tighten the 10-32 locking nut until it touches the mounting bracket and

then tighten

turn more (do not overtighten).

8. If you would like to route the cable through the transom, choose a pass-

through location well above the waterline

➍

and mark it.

9. Use a

in. (16 mm) drill bit to drill a pass-through hole completely

through the transom.

10. Place a cable clamp on the transducer cable

➎

, approximately one third

of the distance between the transducer and the top of the transom or the

pass-through hole.

11. Mark the pilot-hole location for the cable clamp, and, using a

in. (3.2

mm) bit, drill a pilot hole approximately

in. (10 mm) deep.

12. Apply marine sealant to the included 12 mm M4 screw, and attach the

cable clamp to the transom.

13. Repeat steps 10–12 using the other cable clamp.

14. Route the transducer cable to the echo device.

• If you are routing the cable using a pass-through hole, feed it through

the hole you drilled in step 8, and install the cable-entry cover

➍

(page 2).

• If you are not routing the cable using a pass-through hole, route the

cable up and over the top of the transom

➏

Avoid routing the cable close to electrical wires or other sources of

electrical interference.



If you routed the cable through the transom after you installed the transducer,

install the cable entry cover to keep water from entering your boat.

1. Place the cable-entry cover

➊

over the hole and the cable,

with the opening pointing downward, and mark the location

of the two pilot holes.

2. Remove the cable-entry cover, and, using a

in. (3.2 mm)

bit, drill the pilot holes approximately

in. (10 mm) deep.

3. Fill the pass-through hole with marine sealant so that it covers

the cable completely, and that there is excess sealant around

the hole and the cable.

4. Place the cable-entry cover

➊

over the hole and the cable,

with the opening pointing downward.

5. Apply marine sealant to the included 12 mm M4 screws, and attach the

cable-entry cover to the transom.

6. Wipe away any excess marine sealant.

➊

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Echo 100 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echo 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info