Bedienungsanleitung Garmin Echomap Plus serie (Seite 2 von 6) (Englisch)

691424

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Place the swivel mount on the base, and replace the 10 mm

M6×1 Phillips screw.

Seal the cable pass-through holes with marine sealant.

Preparing to Run Cables under the Mounting Surface

NOTICE

Use pan-head screws or bolts when securing the swivel-mount

base. Screws or bolts with countersunk heads damage the

base.

Before you can prepare the swivel-mount base, you must

choose the location to install the mount and decide whether to

attach the mount using screws or bolts.

Remove the 10 mm M6x1 Phillips screw

and separate the

swivel mount

from the base

Orient the swivel base so the pass-through holes

face the

desired direction.

Using the swivel base as a template, mark the pilot hole

locations

Mark the cable routing hole

Using the appropriate drill bit for the hardware, drill the three

pilot holes.

Using a 16 mm (

in.) drill bit, drill the cable-routing hole.

Fastening the Swivel Mount with the Cables Running

through the Mount

You should complete this procedure only when running the

power and transducer cables under the mounting surface and

through the swivel-mount base.

Feed the cables through the 16 mm (

in.) center hole you

drilled when preparing to run cables beneath the mounting

surface.

Place the base on the mounting surface.

Route the cables through the cable pass-through holes.

Loosely fasten the base using the appropriate screws or

bolts.

Place the swivel mount on the base, but do not fasten it.

Place the cradle or device into the swivel mount (Installing

the Device in the Cradle, page 4).

Pull out enough slack from the power and transducer cables

so the mount can fully swivel to the desired positions when

the cables are connected.

Remove the cradle and the swivel mount from the base.

Apply marine sealant to the 16 mm (

in.) center hole and to

the cable pass-through holes.

Securely fasten the base with the appropriate screws or

bolts.

Place the swivel mount on the base, and fasten it using the

included 10 mm M6×1 Phillips screw.

Installing the Cradle in the Mount

Pull up the locking arm

Place the cradle into the swivel mount

Tilt the mount to the desired viewing angle.

Press down the locking arm.

Installing the Cables and Connectors

Wiring to Power

Route the power cable from the mount to the boat battery or

fuse block.

If necessary, extend the wires using 0.82 mm

(18 AWG) or

larger wire.

Connect the red wire to the positive terminal on the battery or

fuse block, and connect the black wire to the negative

terminal.

Wiring Harness

• The wiring harness is used for NMEA

0183 devices, and to

share route and waypoint information.

• The wiring harness connects the device to power and NMEA

0183 devices.

• The device has one internal NMEA 0183 port that is used to

connect to NMEA 0183 compliant devices.

• If it is necessary to extend the power and ground wires, you

must use 0.82 mm

(18 AWG) or larger wire.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Echomap Plus serie Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echomap Plus serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info