Bedienungsanleitung Garmin ECHOMAP Ultra 100 (Seite 1 von 4) (Englisch)

691421

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

ECHOMAP

™

ULTRA 100/120

SERIES

INSTALLATION

INSTRUCTIONS

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, install the device according to these instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin

Product Support.

Tools Needed

• Drill

• Drill bits

◦ Bail mount: drill bits and screws appropriate for the

surface and hardware

◦ Flush mount: 3.2 mm (

in.) and 9.5 mm (

in.) drill bits

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine sealant (optional)

Mounting Considerations

You can flush mount the device in the dashboard or bail mount

the device on the dashboard.

When selecting a mounting location, observe these

considerations.

• The mounting location must provide a clear view of the

screen and access to the keys on the device.

• The mounting location must be sturdy enough to support the

device and the mount.

• The cables must be long enough to connect the components

to each other and to power.

• To avoid interference with a magnetic compass, do not install

the device closer to a compass than the compass-safe

distance value listed in the product specifications.

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

Select the mounting hardware appropriate for your mounting

surface and for the bail-mount bracket.

Using the bail-mount bracket as a template, mark the pilot

holes through the screw holes .

Using a drill bit appropriate for the mounting hardware, drill

the four pilot holes.

Using the selected mounting hardware, secure the bail-mount

bracket to the mounting surface.

Remove the weather caps from the connectors.

Place the cradle into the bail-mount bracket, and tighten

the bail-mount knobs .

Connect all necessary cables to the cradle, and spin the

locking rings clockwise to lock the cables to the cradle.

TIP: To prevent corrosion of the metal contacts, cover

unused connectos with the attached weather caps.

Flush Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

Using a metal pry tool such as a screwdriver can damage the

trim caps and the device. Use a plastic pry tool when possible.

You can mount the device in your dashboard using the flush-

mount template and appropriate hardware.

Trim the template and make sure it fits in the location where

you want to mount the device.

Secure the template to the mounting location.

Using a 13 mm (

in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw or rotary cutting tool, cut the mounting surface

along the inside of the solid line indicated on the template.

Place the device into the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the hole.

Use a pry tool, such as a flat piece of plastic or a screwdriver,

to carefully pry up the corners of the trim caps, and remove

the trim caps.

March 2019

190-02536-02_0A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin ECHOMAP Ultra 100 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin ECHOMAP Ultra 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info