Bedienungsanleitung Garmin GC 12 (Seite 1 von 2) (Englisch)

691893

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

™

12 MARINE CAMERA

INSTALLATION

INSTRUCTIONS

Mounting Considerations

You can mount the camera upside-down or sideways. You can

reverse the camera image to use in rearview mode. See your

chartplotter owner's manual for instructions.

You should mount the camera in a location where it is

• not an obstacle in doorways or walkways.

• not exposed to extreme temperatures.

• not exposed to gas or oil.

• not exposed to radioactivity.

• not facing into direct sunlight or a direct reflection of sunlight.

Tools Needed

• 1 A fuse or circuit breaker

• Drill and 2 mm (

in.) drill bit

Mounting the Camera

Secure the template

to the mounting location.

Using a 2 mm (

in.) drill bit, drill the pilot holes.

Adjust the dome base

to the correct orientation for your

desired camera tilt.

Secure the dome base to the mounting location using the

included tapping screws

Insert the camera

into the dome base.

Secure the set screws

into the dome front

using the

included wrench.

Installation Considerations

You must connect the camera power wire to the battery through

a 1 A fuse or circuit breaker. If you do not use a fuse or circuit

breaker, the camera can malfunction.

Some Garmin

GPSMAP

chartplotters have a built-in CVBS

video encoder. Video from the camera or cameras appears on

all chartplotters on the network when plugged into a single

CVBS IN port. Go to www.garmin.com/manuals/gc12 for a list of

compatible GPSMAP chartplotters.

If you want to use more than one camera or the chartplotter

does not have a CVBS IN port, you must use an encoder.

You can add up to four cameras to one encoder and up to two

encoders to the Garmin Marine Network.

Installation Diagram

GC 12 Marine Camera

1 A fuse or circuit breaker (not included)*

12 Vdc Power source

BNC to BNC Coax Video Cable (not included)

Compatible Garmin chartplotter

*You must connect the camera power wire to the battery through

a 1 A fuse or circuit breaker. If you omit a fuse or circuit breaker,

the camera can malfunction.

Installation With Encoder Diagram

You can add more than one camera to your network when you

use an encoder.

GC 12 Marine Camera

1 A fuse or circuit breaker (required, not included)*

12 Vdc Power source

BNC to BNC Coax Video Cable (not included)

Network cable

Power-over-Ethernet isolation coupler (GPN 010-10580-10)

Garmin Marine Network cable

Axis

Q7424 Encoder (optional/not included)

Compatible Garmin chartplotter

*You must connect the camera power wire to the battery through

a 1 A fuse or circuit breaker. If you omit a fuse or circuit breaker,

the camera can malfunction.

Troubleshooting

Video Does Not Appear on the Chartplotter Screen

• Verify all cables are firmly connected.

• Verify the video cable is connected to the camera video

output port.

Image on the Chartplotter Screen is Dim or Dark

• Verify the lens is clean. If necessary, wipe the lens with a

soft, clean cloth.

• If the camera is exposed to too much direct light, change the

camera position or location.

August 2018

190-01087-01_0A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GC 12 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GC 12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info