Bedienungsanleitung Garmin GCV10 (Seite 2 von 4) (Englisch)

691444

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Connect the bare-wire end of the power cable to a 12 Vdc

power source and to ground.

Align the notch on the end of the power cable with the power

port on the device, and press the cable into place.

Tighten the locking ring.

Repeat steps 3 and 4 for the network and transducer cables.

Installation Diagram

You can use this diagram to identify the connection points from

your sounder to the network, power, and transducer.

Item Description

Chartplotter

GCV 10

Power Source

Transducer

Cable Routing Grommets

NOTICE

Cable routing grommets do not create a waterproof seal. To

create a waterproof seal, apply a marine sealant around the

grommet and cable after installation. Be sure to test the system

before sealing the grommets.

When routing cables through your boat, it may be necessary to

drill holes to route the connector ends of the cables. A rubber

grommet is provided to cover the cable hole for a finished look.

You can purchase additional grommets from your Garmin

dealer or directly from Garmin at www.garmin.com.

Installing the Cable Grommet

Mark the location where you want to route the cable.

Using a 32 mm (1¼ in.) paddle drill bit or hole saw, drill the

installation hole.

Route the cable through the hole to the sounder.

Spread the grommet apart at the split, and place it around

the cable.

Firmly push the grommet into the installation hole until it is

seated.

Apply marine sealant, as needed, to weatherproof the

installation hole.

Blink Codes

After the sounder is installed, it turns on when the chartplotter is

turned on. The two-color (green and red) LED on the sounder

indicates its operational status.

LED

Color

State Status

Green Slow blink The sounder is connected to a chartplotter

and is operating properly. You should see

sonar data on the chartplotter.

Red Slow blink The sounder is turned on, but is not

connected to a chartplotter, or is waiting to

connect to a chartplotter. If the sounder is

connected to the chartplotter and this code

persists, check the wiring connections.

Red/

Green

Slow blink The sounder is in test mode.

Red Rapid blink

sequence

System error. The chartplotter displays a

message indicating the type of failure. When

the error condition is fixed, the sounder must

be completely disconnected from and

reconnected to its power source to clear the

error.

Specifications

Specification Measurement

Size (H×W×D) 251 x 192 x 66 mm (9.9 x 7.6 x 2.6 in.)

Weight 845 g (1.86 lb.)

Case Material Fully gasketed, polycarbonate plastic, water

resistant to IEC 60529-IPX7

Temperature Range From -15° to 70°C (from 5° to 158°F)

Power Input From 10 to 35 Vdc

Power usage 10.5 W maximum

Fuse 4.0 A, mini 42 Vdc, fast-acting, blade-type

Compass Safe

Distance

260 mm (10.2 in. )

Transmit Power (RMS)* 500 W per element (1,500 W combined)

*dependent upon transducer rating and depth

Frequency 455/800 kHz

Depth** 229 m (750 ft) down; 153 m (500 ft) side

**maximum depth, dependent upon

transducer, water salinity, bottom type, and

other water conditions

Data Output Garmin Marine Network

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GCV10 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GCV10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info