Bedienungsanleitung Garmin GPSMAP 702 series (Seite 2 von 8) (Englisch)

657716

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of all cables.

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. It is recommended to apply an anti-seize

lubricant on the screws before installing them.

You can use the included bracket to bail mount the device on a

flat surface.

Using the bail-mount bracket

as a template, mark the pilot

holes

Using a 3.2 mm (

in.) drill bit, drill the pilot holes.

Secure the bail-mount bracket to the surface using the

included M4 wood screws

Install the bail-mount knobs

on the sides of the device.

Place the device in the bail-mount bracket, and tighten the

bail-mount knobs.

Install the trim caps by snapping them in place around the

edges of the device.

Flush Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

The included template and hardware can be used to flush mount

the device in your dashboard. There are three options for

hardware based on the mounting surface material.

• You can drill pilot holes and use the included wood screws.

• You can drill holes and use the included nut plates and

machine screws. The nut plates can add stability to a thinner

surface.

• You can punch and tap holes, and use the included machine

screws.

Trim the template, and make sure it fits in the location where

you want to mount the device.

Secure the template to the mounting location.

Using a 13 mm (

in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw or a rotary tool, cut the mounting surface

along the inside line on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

If necessary, remove the trim caps.

NOTICE

Use a plastic pry tool when possible. Using a metal pry tool,

such as a screwdriver, can damage the trim caps and the

device.

After the device fits correctly in the cutout, ensure the

mounting holes on the device line up with the larger holes on

the template.

If the mounting holes on the device do not line up, mark the

new hole locations.

Based on your mounting surface and model, drill or punch

and tap the larger holes:

• For the included wood screws on 702 models, drill 2 mm

(

in.) holes, and skip to step 18.

• For the included wood screws on 902 models, drill 3.2 mm

(

in.) holes, and skip to step 18.

• For the included nut plate and machine screws, drill 6 mm

(

in.) holes in the larger hole locations.

• For the included machine screws without the nut plate on

702 models, punch and tap M3.5 holes, and skip to step

18.

• For the included machine screws without the nut plate on

902 models, punch and tap M4 holes, and skip to step 18.

If you are using a nut plate, starting in one corner of the

template, place a nut plate

over the larger hole

drilled in

the previous step.

The smaller hole

on the nut plate should line up with the

smaller hole on the template.

If the smaller hole on the nut plate does not line up with the

smaller hole on the template, mark the new hole location.

If you are using a nut plate, drill a 4 mm (

in.) hole in the

smaller hole location.

Repeat to verify placement of the remaining nut plates and

holes on the template.

Remove the template from the mounting surface.

Starting in one corner of the mounting location, place a nut

plate

on the back of the mounting surface, lining up the

large and small holes.

The raised portion of the nut plate should fit into the larger

hole.

Secure the nut plates to the mounting surface by fastening

the smaller machine screws

through the smaller holes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 702 series Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 702 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info