Bedienungsanleitung Garmin GPSMAP 8000 series (Seite 3 von 14) (Englisch)

658524

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Secure the device to the mounting surface using the included

M4 screws

Insert the included plugs over each of the M4 screw heads.

Install the decorative bezel by snapping it in place around the

edges of the device.

Card Reader Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

The card reader can be flush mounted in the dashboard using

the included hardware. When selecting a mounting location,

observe these considerations.

• The card reader should be mounted in an accessible

location. You must be able to access the card reader when

necessary to insert and remove memory cards containing

additional mapping and device updates, and to transfer user

data.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of the cables.

Mounting the Card Reader

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case

and the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

The included template and hardware can be used to flush

mount the device at the selected location.

Trim the flush-mount template and make sure it fits in the

location where you want to mount the device.

Remove the protective liner from the back of the template

and adhere it to the location where you want to mount the

device.

Using a 6 mm (¼ in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw, cut the mounting surface along the inside of

the solid line indicated on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the device

fits correctly in the cutout, make sure the

mounting holes on the device line up with the pilot holes

on the template.

If the mounting holes on the device do not line up, mark the

new pilot-hole locations.

Using a center punch, indent the pilot holes and drill the

clearance counterbore through the gel-coat layer as advised

in the notice.

Remove the template from the mounting surface.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

Place the device into the cutout.

Secure the device to the mounting surface using the included

screws

Install the decorative bezel by snapping it in place around the

edges of the device.

Antenna Mounting Considerations

You can mount the antenna on a flat surface, install it under

fiberglass, or attach it to a standard 1 in. OD, 14 threads per

inch, pipe-threaded pole (not included). You can route the cable

outside of the pole or through the pole. For best performance,

consider these guidelines when selecting the antenna mounting

location.

• To ensure the best reception, the antenna should be

mounted in a location that has a clear, unobstructed view of

the sky in all directions

• The antenna should not be mounted where it is shaded by

the superstructure of the boat

, a radome antenna, or the

mast.

• The antenna should not be mounted near the engine or other

sources of Electromagnetic Interference (EMI)

• If a radar is present, the antenna should be mounted above

the path of the radar

. If necessary, the antenna may be

mounted below the path of the radar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8000 series Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8000 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info