Bedienungsanleitung Garmin GT34UHD (Seite 3 von 4) (Englisch)

691442

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

deep can adversely affect the performance of the boat and put

the transducer at risk of striking underwater objects.

Test the transom-mount transducer installation in open water

free of obstacles. Pay attention to your surroundings as you test

the transducer.

With the boat in the water, turn on the chartplotter.

Drive the boat at a slow speed. If the chartplotter appears to

be working properly, gradually increase speed while

observing the chartplotter.

If the sonar signal is suddenly lost or the bottom return is

severely degraded, note the speed at which this occurs.

Return the boat to the speed at which the signal was lost,

and make moderate turns in both directions while observing

the chartplotter.

If the signal strength improves while turning, adjust the

transducer so that it extends another

in. (3 mm) below the

transom of the boat.

Repeat steps 2–4 until the degradation is eliminated.

If the signal does not improve, move the transducer to a

different location on the transom, and repeat the test.

Installing the Transducer on a Trolling Motor

Assembling the Trolling Motor Mount

Using the 8 mm M4 screws

and 4 mm star washers

attach the trolling motor mount

to the transducer

Route the cable through the cable exit

so the cable is on

the top side of the trolling motor housing when stowed.

Installing the Transducer on a Trolling Motor

NOTICE

Do not cut the transducer cable. Cutting the transducer cable

will void your warranty.

Insert the hose clamp

through the slot on the transducer

mount

, until equal lengths extend on both sides of the

mount.

Place the transducer mount against the body of the trolling

motor with the narrow end of the transducer pointed away

from the propeller.

Secure the hose clamp around the body of the trolling motor,

and tighten the hose clamp.

Position the transducer so it is parallel to the bottom when in

use.

Use the included cable ties to secure the transducer cable.

Route the transducer cable to the installation location of the

sounder while taking these precautions.

• The cable should not be routed close to electrical wires or

other sources of electrical interference.

• The cable must not be pinched when the trolling motor is

deployed or stowed.

Specifications

Dimensions (L x W x H) 197.93 x 38.21 x 23.14 mm (7.8 x 1.5 x

0.9 in.)

Operating temperature

range

From 0° to 50°C (from 32° to 122°F)

Storage temperature

range

From -40° to 70°C (from -40° to 158°F)

Transmit power (RMS) 500 W

Frequencies Garmin ClearVü: CHIRP 820 kHz

SideVü: CHIRP 1.12 MHz

Maximum depth/range* Garmin ClearVü

™

: 61 m (200 ft.)

SideVü: 38 m (125 ft.) each side, 76 m

(250 ft.) total

*Dependent upon water salinity, bottom type, and other water

conditions.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,

registered in the USA and other countries. These trademarks may not be used without

the express permission of Garmin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GT34UHD Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GT34UHD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info