Bedienungsanleitung Garmin Striker Cast (Seite 6 von 10) (Englisch)

740399

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

TIP: It is recommended to tow the device behind canoes and

kayaks, but not recommended to tow the device behind

power boats while underway.

Sonar Screen

Depth

Water temperature

Water surface

Fish

Depth indicator as the sonar data screen scrolls from right to left

Structure

TIP: If the sonar view does not show returns, a small air bubble

might be trapped on the pins near the power connector. Re-cast

the device or tug on the line to clear the bubble.

TIP: If the sonar view shows repetitive bands, the STRIKER

Cast device is likely in very shallow water. The bands are echos

in the sonar returns. You can adjust the range to resolve this

problem.

Adjusting the Level of Detail

You can control the level of detail and noise shown on the sonar

screen by adjusting the gain.

If you want to see the highest intensity signal returns on the

screen, you can lower the gain or brightness to remove lower

intensity returns and noise. If you want to see all return

information, you can increase the gain or brightness to see more

information on the screen. This also increases noise, and can

make it more difficult to recognize actual returns.

Select Sonar > .

Under Gain, select an option:

• To allow the device to adjust the gain automatically, select

Auto.

• To increase or decrease the gain manually, use the slider.

Adjusting the Range of the Depth Scale

Allowing the device to adjust the range automatically keeps the

bottom within the lower or outer third of the sonar screen, and

can be useful for tracking a bottom that has minimal or moderate

terrain changes.

Manually adjusting the range enables you to view a specified

range, which can be useful for tracking a bottom that has large

terrain changes, such as a drop-offs or cliffs. The bottom can

appear on the screen as long as it appears within the range you

have set.

Select Sonar .

Under Range, select an option:

• To allow the device to adjust the range automatically,

select Auto.

• To increase or decrease the range manually, use the

slider.

Sonar Settings

Select Sonar > > More Settings.

View: Shows a Traditional sonar view or a Flasher view (Flasher

View, page 2).

Frequency: Adjusts the frequency to adapt the sonar for your

particular goals and the present depth of the water.

The 455 kHz setting uses a narrower beam width and is

better for rough sea conditions. Bottom definition and

thermocline definition can be better when using a higher

frequency.

The 260 kHz setting uses a wider beam width, which covers

a larger area and can allow you to see more targets, but also

could generate more surface noise. Wider beam widths

generate larger arches for fish target returns, making them

ideal for locating fish. Wider beam widths also perform better

in deep water, because the lower frequency has better deep

water penetration. They can be used to search for structures

such as brush piles.

Scroll Speed: Sets the rate at which the sonar scrolls from right

to left. A higher scroll speed shows more detail, especially

while moving or trolling. A lower scroll speed displays sonar

information on the screen longer.

A-Scope: Displays a vertical flasher along the right side of the

screen that shows instantaneously the range to targets along

a scale.

Fish Symbols: Sets how the sonar displays suspended targets.

Restore Sonar Defaults: Restores the factory default settings

for the sonar view.

Turning On the Flasher

Select Sonar > > More Settings > View > Flasher >

Back.

Flasher View

The flasher shows sonar information on a circular depth scale,

indicating what is beneath the STRIKER Cast transducer. The

flasher is organized as a ring that starts at the top and

progresses clockwise. Depth is indicated by the scale inside the

ring. Sonar information flashes on the ring when it is received at

the depth indicated.

The flasher colors indicate different strengths of the sonar

return. The default color scheme follows a traditional sonar color

palette, in which yellow indicates the strongest return, orange

indicates a strong return, red indicates a weaker return, blue

indicates the weakest return, and white indicates no return.

Water temperature

Depth at the location of the STRIKER Cast transducer

Sonar returns

Status Icons

The status icons on the Sonar page provide information about

the STRIKER Cast device.

2 Fishing with the STRIKER Cast Device

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Striker Cast Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Striker Cast

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info