Bedienungsanleitung Garmin VHF 110i (Seite 2 von 10) (Englisch)

665016

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

2 VHF 100/200 Series Radio Installation Instructions

Installing your VHF 100/200 Series Radio

1. Select a location (page 2).

2. Mount the radio (page 2).

3. Connect the radio to power (page 4).

4. Connect the radio to an antenna (page 5).

5 Mount the microphone hangar (page 5).

Although they are not necessary to use your radio, these instructions cover the following additional installation options.

Connecting the radio to a chartplotter (page 5)

Connecting the radio to a hailer horn (page 7)

Connecting the radio to an external speaker (page 8)

Connecting the GHS

™

10 or GHS 10i handset or a relocation microphone (page 8)

Step 1: Select a Location for the VHF 100/200 Series Radio

Consider the following when you select an installation location:

Provides optimal viewing.

Allows easy access to the radio controls and handset.

Is strong enough to support the weight of the radio and protect it from excessive vibration or shock.

Allows room for the routing and connection of the cables for power and data. There should be at least 5 in. (127 mm) of clearance

behind the case.

Is located at least 20 in. (500 mm) from a magnetic compass.

Is in an area that minimizes exposure to extreme weather conditions.

NOTE: The temperature range for the VHF 100/200 series radios is from 14°F to 122°F (from -10°C to 50°C). Extended exposure to temperatures

outside this range (in storage or operating conditions) may cause failure of the LCD screen or other components. This type of failure and related

consequences are not covered by the manufacturer’s limited warranty.

Step 2: Mount the VHF 100/200 Series Radio

You can mount your radio in one of two ways:

Bail Mount—mount the radio onto the bracket that attaches to the console or overhead.

Flush Mount—use the ush-mount kit to mount the radio into a at panel.

Bail Mounting the VHF 100/200 Series Radio

In addition to the included mounting bracket, mounting knobs, and three of the 4.2 × 25 mm panhead mounting screws, bail mounting the

VHF 100/200 series radio requires the following tools (not included):

Phillips screwdriver

Drill and 9/64 in. (3.5 mm) drill bit

Center punch and hammer

Customer-supplied mounting hardware (optional) - bolts, nuts, and washers

To mount the bracket assembly:

1. Using the base of the bracket as a template, mark the location of the three holes (two screws towards the front, one screw towards the

back).

2. Using the center punch, indent the center of each of the three mounting-hole locations.

3. Drill the mounting holes, using a 9/64 in. (3.5 mm) drill bit.

4. Secure the base with the three 4.2 × 25 mm included screws or, if desired, secure with appropriate bolts, nuts, and washers (not

included).

To install the VHF 100/200 series radio on the mounting bracket:

1. Loosely attach the mounting knobs to the VHF 100/200 series radio.

2. Slide the radio onto the mounting bracket, and tighten the mounting knobs.

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin VHF 110i Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin VHF 110i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info