Bedienungsanleitung Garmin Vivosmart HR plus (Seite 12 von 16) (Englisch)

657428

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Tips for Charging Your Device

• Connect the charger securely to the device to charge it using

the USB cable (Charging the Device, page 7).

You can charge the device by plugging the USB cable into a

Garmin approved AC adapter with a standard wall outlet or a

USB port on your computer. Charging a fully depleted battery

takes about 60 to 90 minutes.

• Remove the charger from the device after the battery charge

level icon is full and stops flashing.

• View the remaining battery power on the device

information screen (Viewing Device Information, page 7).

Using the Device in Charging Mode

You can interact with the device while charging it with your

computer. For example, you can use Bluetooth connected

features or customize device settings.

Connect the device to your computer using the USB cable.

Select to exit USB mass storage mode.

Device Care

NOTICE

Avoid extreme shock and harsh treatment, because it can

degrade the life of the product.

Avoid pressing the keys under water.

Do not use a sharp object to clean the device.

Never use a hard or sharp object to operate the touchscreen, or

damage may result.

Avoid chemical cleaners, solvents, and insect repellents that can

damage plastic components and finishes.

Thoroughly rinse the device with fresh water after exposure to

chlorine, salt water, sunscreen, cosmetics, alcohol, or other

harsh chemicals. Prolonged exposure to these substances can

damage the case.

Do not store the device where prolonged exposure to extreme

temperatures can occur, because it can cause permanent

damage.

Do not remove the bands.

Cleaning the Device

NOTICE

Even small amounts of sweat or moisture can cause corrosion

of the electrical contacts when connected to a charger.

Corrosion can prevent charging and data transfer.

Wipe the device using a cloth dampened with a mild

detergent solution.

Wipe it dry.

After cleaning, allow the device to dry completely.

TIP: For more information, go to www.garmin.com/fitandcare.

Troubleshooting

Tips for Erratic Heart Rate Data

If the heart rate data is erratic or does not appear, you can try

these tips.

• Clean and dry your arm before putting on the device.

• Avoid wearing sunscreen, lotion, and insect repellent under

the device.

• Avoid scratching the heart rate sensor on the back of the

device.

• Wear the device above your wrist bone. The device should

be snug but comfortable.

• Wait until the icon is solid before starting your activity.

• Warm up for 5 to 10 minutes and get a heart rate reading

before starting your activity.

NOTE: In cold environments, warm up indoors.

• Rinse the device with fresh water after each workout.

My intensity minutes are flashing

When you exercise at an intensity level that qualifies toward

your intensity minutes goal, the intensity minutes flash.

Exercise for at least 10 consecutive minutes at a moderate or

vigorous intensity level.

The floors climbed amount does not seem

accurate

Your device uses an internal barometer to measure elevation

changes as you climb floors. A floor climbed is equal to 3 m

(10 ft.).

• Locate the small barometer holes on the back of the device,

near the charging contacts, and clean the area around the

charging contacts.

The barometer performance may be affected if the barometer

holes are obstructed. You can use canned air to clear

obstructions. You can rinse the device with water to clean the

area.

After cleaning, allow the device to dry completely.

• Avoid holding handrails or skipping steps while climbing

stairs.

Maximizing Battery Life

• Turn off the Auto Backlight setting (Device Settings on Your

Garmin Connect Account, page 6).

• Decrease the backlight brightness (Device Settings, page 7).

• In your smartphone notification center settings, limit the

notifications that appear on your vívosmart HR/HR+ device

(Managing Notifications, page 5).

• Turn off smart notifications (Bluetooth Settings, page 5).

• Turn off Bluetooth wireless technology when you are not

using connected features (Turning Off Bluetooth Wireless

Technology, page 5).

• Stop broadcasting heart rate data to paired Garmin devices

(Broadcasting Heart Rate Data to Garmin

Devices, page 3).

• Turn off wrist-based heart rate monitoring (Device Settings,

page 7).

NOTE: Wrist-based heart rate monitoring is used to calculate

vigorous intensity minutes and calories burned.

Resetting the Device

If the device stops responding, you may need to reset it. This

does not erase any of your data or settings. You must set the

time of day again.

Hold the device key for 10 seconds.

The device turns off.

Hold the device key for one second to turn on the device.

Restoring All Default Settings

You can restore all of the device settings back to the factory

default values.

NOTE: This deletes all user-entered information and activity

history.

Press the device key to view the menu.

Select > Restore Defaults > .

8 Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vivosmart HR plus Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info