Bedienungsanleitung GE 15136 (Seite 2 von 3) (Englisch)

557957

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Initial Set Up:

1. Push the “R” button before programming to clear out any settings. Once

the “R” button is pressed the screen will begin to ﬂash. A paperclip may be

needed for this step.

(If the “R” button appears to stick down, use a paperclip to maneuver

it until it pops back up. The screen will ﬂash if the button is popped up

successfully.)

2. Press the “Clock” button and the screen will stop ﬂashing and be ready for

programming.

Setting the Current Time:

1. Press and Hold the “Clock” button during the entire setting.

2. Press the “H+” button to set the hours.

3. Press the “M+” button to set the minutes.

4. Press the “Day” button to set the day of the week.

5. Release the “Clock” button.

Programming ON/OFF Settings:

1. Press the “Timer” button once and the TIMER 1 ON - - : - - appears.

2. Press the “H+” and “M+” button to set the hours and minutes to the

desired time.

3. Press the “Day” button to select the day(s) the setting will be active. Refer

to the Multiple Weekday Group below to see the available settings.

4. Press the “Timer” button to store the setting and proceed to the next

setting TIMER 1 OFF - - : - -.

5. Repeat for all remaining setting options (9 Total ON/OFF settings). Once

completed press the “Clock” button to return to the main display.

Multiple Weekday Groups:

Apart from individual week days, pressing the “Day” button also selects

multiple day combinations such as:

‧ Monday thru Friday ‧ Tuesday & Thursday & Saturday

‧ Saturday & Sunday ‧ Monday thru Wednesday

‧ Monday thru Saturday ‧ Thursday thru Saturday

‧ Monday & Wednesday & Friday ‧ Monday thru Sunday

After setting a single day or a multi-day-combination the programmed timer

settings will be carried out on each of the week-days at the same time.

conduits. When using non-metallic conduit or cable, connect

the ground wires of all cables together with the provided

wire nut. When metallic conduit is used; as the grounding

connection, use grounding type bushing and a jumper wire

between each conduit.

Dipswitch Conﬁguration

WARNING: Failure to properly conﬁgure the dipswitch will result

in damage to the unit and void any warranty! Before installing

and wiring the GE Time Switch, proper conﬁguration must

be selected. Unit is shipped with DIP Switches set for 277VAC

Input Voltage. Also, do not check circuits by “sparking” wires to

terminals. Damage to timer may result.

4. Determine the input voltage which will be applied to the timer.

(120V AC, 208-240V AC, or 277V AC)

5. Set the DIP Switch according to the diagram below.

6. Reinstall interior cover panel. Opposite of step 1.

TIMERN CN O

COM

NC2

NO2

COM2

LOAD

TIMERN CN O

COM

TO 200/240/277V LINE

TO 120V LINE

NC2

NO2

COM2

LOAD

TIMERN CN O

COM

TO 24V LINE

NC2

NO2

COM2

LOAD

TO 120V LINE

TO LOAD

120V Timer, 120V Load and 24V Load

Wired as Single Throw

200/240/277V Timer, 200/240/277V Load, Double Break

Wired as Single Throw

120V Timer, 200/240/277V Load Double Break

Wired as Single Throw

Typical Wiring Diagrams—DPDT

TO POWER SUPPLY

TO POWER SUPPLY 1

TO POWER SUPPLY 2

Timer and Load, Same Voltage

Wired as Single Throw

TO LOAD

TO 120V LINE

HIGH

LOW

COM

LOAD

NCTIMERN OC OM

TIMERN CN OC OM

120V Two Speed Fan

Wired as Double Throw

Timer and Load, Different Voltage

Wired as Single Throw

Typical Wiring Diagrams—SPDT

Field Wiring

Timer Internab Wiring

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

105

MINIMUM COPPER

WIRE SIZE (AWG)

MAX. LOAD (AMP) MIN. INSULATION

TEMP(°C)

Figure 1

Override

(Manual ON/OFF Switched)

Timer

(9 Programs Setting)

Clock

(Current Time Setting)

LCD

(Function Figures)

(Reset)

H-

(Hours Setting)

M-

(Minutes Setting)

Day

(Days Setting)

Operating Instructions

Basic Settings

120VAC

OFF

277VAC (Default)

OFF

208~240VAC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

GE 15136 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info