Bedienungsanleitung Geba Tronic TCS - Cody 2 (Seite 4 von 4) (Englisch)

544618

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Please read first - then do programming!!!

Before programming your TCS-Cody with your personal codes, please check the faultless

function of the appliance with the help of the factory‘s pass code 1234 and the key-operated

pushbutton.

Normally, any programming is made via your personal master code. In order to get familiar

with that kind of programming, you start with the input of a new pass code, which replaces

the one preset by the factory (1234). The procedure is explained under item

“Program 2“.

After that please change the master code to the string of digits you choose.

ATTENTION

In case you made a mistake on programming, you can start again by actuation of the key-

operated pushbutton (`*`).

Program 1

Input of a new master code

Assembly Instructions

Assembly of the CODY keyboard:

1. By slightly pushing the two latches at the right and left side of the keyboard

from behind to the edge, remove the small frame from the keyboard.

2. Now you see two fixingholes (diam. = 4 mm) at the front of the keyboard.

By means of these you can fix the keyboard onto the wall.

3. Connect the keyboard to the logic unit by means of a twin-cable (up to 5 m long).

There is no particular polarity for the twin wires.

4. Now re-fix the small frame.

5. It is possible to connect in parallel up to four keyboards if a thin connection cable, max.

total line cross-section 1.5 mm

, is used.

Keyboards connected in this way must not be operated simultaneously.

Assembly of the logic unit (inside area):

1. Put the screw-driver into the gap of the enclosure front, push the screw-driver up and

open the enclosure.

2. Remove the control PCB (which is force fitted to the inside of the enclosure).

3. Locate the screwed glands supplied (sealing nipple left side) in the

enclosure and replace the PCB. (Please ensure PCB is firmly in position)

4. Bore the fastening holes and fix the enclosure bracket at the wall.

5. The wires for the keyboard ensure through the left cable entry (sealing nipple), the wires

for the relay contacts through the two middle cable entries and the wires for the supply

voltage ensure through the right cable entry. Ensure tight seating of sealing nipple and

cable gland, otherwise the water-protection ot the appliance cannot be assured.

6. According to connection diagram connect the wires to the corresponding

terminals:

Connections:

Keyboard, door 1 (e.g. garage door drive), door 2 (e.g. garage door drive), supply voltage

Programming Instructions

Input 8-digit

master code

Input 8-digit

NEW master code

Sound

signal

2 x long

Push key

button

Push key

button

Sound signal

1 x long

Sound signal

1 x short

Push key

button

The new master code is now stored !

Spannungsversorgung

je nach Gerätetyp

Tastatur

Trafo

Generalreset

L1 N PE

Tor 1

Tor 2

Cody 1/2

Connection diagram:

keyboard

door 1

door 2

power supply

GENERAL RESET

Push Button

Trans-

former

industial controls

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Geba Tronic TCS - Cody 2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Geba Tronic TCS - Cody 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info