479841
3
Zoom out
Zoom in
Vorherige Seite
1/7
Nächste Seite
Dip switch programming table.
1 ON Current drawn active
OFF Current drawn isolated
2 ON Acoustic activation/de-activation isolated
OFF Acoustic activation/de-activation active
3 ON Passive arming active
OFF Passive arming isolated
4 ON Locking control 1,5 sec.
OFF Locking control 25 sec.
TECHNICAL DATA
Power supply 12 VDC
Current drawn alarm ON 16 mA
Current drawn alarm OFF 14 mA
Working temperature -30° + 85°
Engine immobilisation relay contact capacity 8A to 20°C
Central door locking relay contact capacity 10 A to 20°C
Alarm cycle 30 seconds
Siren audible level at 1 meter in open space > 118 dB
Minimum power absorption required to trigger 5W
Current for control positive alarm armed 500 mA
This device has been designed to be fitted on all cars with a power supply of 12V and with
the negative connected to the body work.
Attention: do not turn the unit on with the key switch before the installation is complete. You
must then wait for a maximum of 60 minutes before completing the self-powered test. All
other alarm functions will perform as standard.
If You want to wash the engine of the car, please take care do not steam clean.
The manufacturer and his agents declines all responsibility for any possible defect or failure to the
device and to the vehicle’s electric system due to incorrect installation or to the alteration of the
indicated Technical Features. The alarm system has only a dissuasive function against possible
thefts.
Gemini Trading S.r.l. reserves the right to modify its products without prior notice.
ULTRASONIC MODUL DESCRIPTION
5023GE and 5123GE (for 4202RC-KT and 4203RC-KT)
The 5023 or 5123 sensors protect the vehicle passenger compartment, detect the
door opening or a movement in the passenger compartment and activate the alarm.
Installation instructions :
The connection with the alarm system is easy as the 4202RC and 4203RC wiring
harness is supplied with a connector for the connection of the sensor.
Put the connectors of the sensor’s ultrasonic heads in the appropriate seats : RED
for the connection of the TX head ; WHITE for the connection of the RX head.
Ultrasonic adjustment
- Lower one of the front windows approximately 20 cm.
- Adjust the sensor to a minimum sensitivity ;
- Activate the alarm pushing twice on the transmitter’s button (button 2) verifying all
doors are closed.
- Put an hand through the open windows and move it ; the LED will light
red. Increase the sensitivity till the alarm triggers.
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gemini 4203RC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info