479859
4
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
PAG. 6
PAG. 7
Being closed all the doors of the vehicle, turn the ignition key to “ON”; after 20”,
all doors will be locked.
By turning the ignition key to “OFF”, all doors of the vehicle will be automatically
unlocked.
After programming, this function is obtained simply by turning the ignition key
to “OFF”.
When opening a vehicle's door during passive arming, the arming time count
will be set to zero and the led will be permanently illuminated; when the door is
closed the 45” counting will restart.
LOCKING TIME
The standard locking time of the alarm is set to 0,5”.
In case the vehicle needs a locking time of 6”, you can vary this parameter
during the programming phase.
NOTE: When the comfort function has been activated, let the locking time set
to 0,5”.
In fact, if the locking time is set to 6”, when the alarm is disarmed, the windows
of the vehicle will open.
COMFORT CONTROL
The comfort control allows the automatic regulation of window closing, when
the alarm is armed.
In fact, after this function has been activated, at any alarm arming, the window
winder motor/control unit will receive a 25” command, to close the windows.
To prevent this function from being activated accidentally, the system
continuously monitors the status of the ignition key and the input line of the
DOOR AND BOOT PUSHBUTTONS and therefore does not allow operation of
the locks if the DOORS and BOOT are opened manually while starting the
engine or during the 20” after starting it.
PASSIVE ARMING
Automatic arming allows to have the alarm system active, 45 seconds after the
engine switching “OFF”.
The alarm will indicate the passive arming activation by a long flash of the turn
signals, two flash of the status led and two acoustic signals.
CDL DOUBLE OPENING PULSE
By enabling this function you will obtain, upon deactivation of the system, a
double control pulse on the door-unlocking line (about 0,5 second each).
This allows the opening of the centralized door locks on vehicles having the
diversified door opening (first pulse driver side door opening, second pulse
other doors opening).
This function is active only if the opening/closing time of 0,5” is selected, while
setting the opening/closing timo of 6” will automatically disabled the double
pulse.
PROGRAMMING THE ALARM SYSTEM
Has been previously programmed with standard configuration during
manufacturing procedure by Gemini, and can be modified in any moment
! With alarm being disarmed, open and keep it open the driver side door.
! Turn the ignition key to "ON" position.
! The status led stay on for 0,5 seconds; during this time, push together the
two buttons of the remote control.
! Starting of programming procedure is indicated by two acoustic signals,
one with high tone and one with loud tones, furthermore the led is
permanently illuminated.
! To able and disable the functions, follow the below table, take into
consideration that every time the push button of transmitter is pressed, the
system goes to the following function.
During the programming phases, press the radio control (rough) push-button
n.1, for function activation and the (smooth) push-button n.2, for function de-
activation.
ATTENTION: pay attention to not modify the functions which have been
programmed during the installation.
For the programming modification proceed as follows:
NOTE:
Once the last function has been programmed, the alarm will confirm that
the programming has been disabled with two acoustic signals with low
tone, one acoustic signal with high tone,
! Turn the ignition key to “OFF” position.
by turning the ignition key to
OFF”, in any moment of the programming
procedure, the latter will stop and successive functions will remain unchanged.
!
furthermore the led will be turned
off.
Acoustic signals
Panic alarm or “car finder”
Passive arming
Current absorption sensor
Anti-distraction, automatic
door locking function
Setting of centralized lock
times (0,5 - 6 sec)
25 seconds comfort closure
command
Double impulse in opening
Enabled
Enabled panic
alarm
Disabled
Disabled
Disabled
0,5” selected
Disabled
Disabled
Button N°1- Enable
N°2- Disable
N°1- Enable panic
N°2- Enable
N°1-
N°2-
N°1-
N°2-
Button
Button
Button car-finder
Button Enable
Button Disable
Button N°1- Enable
Button N°2- Disable
Button Enable
Button Disable
Button N°1- Enable 6”
Button N°2- Enable 0,5”
Button N°1- Enable
Button N°2- Disable
Button N°1- Abilita
Button N°2- Disable
FUNCTION
STATE BUTTON
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gemini 7562 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info