479885
3
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
INSTALLER MANUAL - PAGE 05PAGE 04 - INSTALLER MANUAL
INSTALLER MANUAL
BLACK
RED
6-way connector to plug into
the free connector
on the BSI control unit
marked
“EA”
5.0 - COMPLETE ELECTRIC DIAGRAM
CAN BUS signal
LIGHT BLUE (CAN-L)
LIGHT BLUE-GREY (CAN-H)
3
1
6
4
6.0-U
6.1 - CONNECTIONS AND POSITIONING
6.2 - SENSOR ADJUSTMENT
Insert the WHITE connector
.
:
.
LTRASONIC VOLUMETRIC PROTECTION
in the the “W” socket on the control unit.
Insert the RED connector in the “R” socket on the control unit.
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the aeration inlets and orient them towards the center of the rear window
o check sensors proceed as follows
With system disarmed, roll down the front window approx. 20 cm.
Set the trimmer on the control unit to the middle position.
Close doors, bonnet and boot and arm the system.
During the system inhibit arming time, introduce an object in the cabin and move it around; the
status LED will turn off to signal a presence.
If sensibility level is too low, adjust trimmer again and repeat above procedure
!
!
!
!
!
ULTRASONIC
CELLS
CONNECTIONS
SENSIBILITY
ADJUSTMENT
4.0 - CONNECTORS TABLES
Ground
-----
Positive
-----
-----
-----
-----
-----
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-9-
-10-
-11-
-12-
-13-
-14-
-15-
-16-
-17-
-18-
-19-
-20-
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-----
-----
-----
-----
-----
-----
BROWN
BLACK
RED
-----
LIGHT BLUE-GREY
LIGHT BLUE
PINK
GREEN-BLACK
-----
-----
-----
-----
-----
----
BLACK
-----
RED
-----
-----
-----
-----
-----
WIRE FUNCTION
WIRE FUNCTION
POSITION
POSITION
WIRE COLOUR
WIRE COLOUR
4.1 - 20-WAY CONNECTOR
4.2 - 8-WAY CONNECTOR
-----
-----
-----
-----
-----
-----
Grund for external sensor connector
LED negative output
LED positive output
-----
CAN BUS signal (CAN-H)
CAN BUS signal (CAN-L)
Positive output with system armed (+A)
External sensor negative input
-----
-----
-----
-----
-----
-----
For the system to work properly, the “original alarm installed” feature (BSI unit)
must first be enabled via the specific diagnostic tester available at any authorized
Peugeot-Citroën dealer (PSA group).
Moreover, this type of system DOES NOT require that you program the vehicle
code, it is already factory-registered by Gemini.
NEVER PRESS THE PROGRAMMING BUTTON LOCATED NEXT TO THE UNIT
BUILT-IN LED
!
Before carrying out all
electrical connections,
disconnect the
negative battery
terminal and re-
connect again after
completion.
!
Red
Black
Connector for external modules
Pink
Brown
Green-Black
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gemini 931PSA wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info