Bedienungsanleitung Gorenje ec 7969 e w b (Seite 5 von 16) (Englisch)

326234

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Instructions for use, installation and connection

108

Operation

Once the glass ceramic hob is connected to the mains, the

power and clock indicators are switched on for a brief moment,

and eventually disappear. A sound signal confirms the

appliance is ready for use. Only the LED signal lamp for

blocked operation is on, and may be switched off by touching

the sensor.

The hob is equipped with electronic sensors which are

switched on by touching or pressing the sensor surface with

your fingertip. Each sensor reaction is confirmed by the beep.

Always take care to touch only one sensor at the time for a

short period of time (approximately 1 second). If more than one

sensor is pressed at the same time the relevant command is

not accepted. If the touch is prolonged it provokes error mode

and the appliance is switched off.

Do not place any objects upon the sensor surface (error mode)

nor any hot dishes which may damage the sensors. Keep the

sensor surface clean at all times.

Switching the hob on

When the hob is turned off all the hotplates are off and

indicator LED's are off.

To switch the hob on, touch the ON/OFF sensor. The hob is

activated and all power displays indicate »0« for a period of 10

seconds. Using the (+) or (-) sensor you may select the

desired cooking power of a particular hotplate (see Power

Regulation).

Next setting of a particular hotplate should be selected within

ten seconds, otherwise the hob will automatically be switched

off and a short warning beep is heard.

Switching the hotplates on

As long as the indicators are lit the heating power (1...9) may

be selected and altered accordingly by pressing the (-) or (+)

sensor. By the (+) sensor the power is gradually increased to

the maximum level (9), while with the (-) sensor it is reduced

back to 0 (hotplate is switched off). In case you start the setting

by pressing the (-) sensor, the heating power shall immediately

start from the level 9.

Automatic cooking mode

Each hotplate may be switched to automatic cooking mode.

When the automatic cooking mode is activated the hotplate will

operate at maximum power for a limited period of time

(depending upon the power level required for continuation –

see chart) and then automatically switch to the reduced power

level to resume cooking.

Automatic cooking mode may be switched on only in case the

power setting is regulated at maximum setting 9. By touching

the hotplate (+) sensor the decimal dot (•) next to the indicator

starts flashing. Within the next ten seconds press the (-)

sensor and select the power setting (8...1) for cooking. After

the 10 seconds have elapsed the sound signal beeps, the

decimal dot is on for the entire time this function is on. By

touching the (-) or (+) sensor you may vary the heating power

at any desired moment.

Power setti ng Maximum power time

(in seconds)

1 1'10'

2 2'45''

3 4'50''

4 5'30''

5 6'30''

6 1'10''

7 2'45''

8 2'45''

Automatic cooking mode may be switched off by pressing the

(-) sensor. Once the function is switched off there is a beep

heard and the decimal dot disappears.

Switching the complete hob off

The hob is switched off by pressing the main ON/OFF sensor.

The sound signal beeps and all indicators go off, except for

those hotplates which are still hot and display the warning "H"

sign as an indication of the remaining heat.

Switching the hotplate off

Particular hotplate is switched off either by pressing the sensor

(-) to bring the heating power to "0", or by simultaneously

pressing both the (+) and (-) sensor. Display indicates "0" for a

short time, then the hotplate is switched off and the indicator

displays the remaining heat "H".

Switching the extended hotplate rings on (hotplates 2 and

Switch the relevant hotplate ( 2 or 4) and consequently switch

the extended hotplate ring by pressing the relevant sensor (see

the control board illustration). The LED signal lamp above the

indicator displays the extended ring is on. Now select the

random heating power for both hotplate rings together.

Extended ring may be switched off either by consequent

pressing the sensor or by reducing the heating power to "0",

as well as by simultaneous pressing of both the

(-) and (+) sensor. It may of course be switched off also by

switching off the entire hob.

The rear right hotplate (4) is equipped with two extended

hotplate rings. To switch the second ring on, press the special

second ring sensor (top left). The LED signal lamp above the

indicator displays the ring is on. To switch on the third ring

press the same sensor once again, another LED signal lamp is

on. Both extended rings are switched off by repeated pressing

the sensor. They may also be switched off by switching off the

relevant hotplate or the entire hob.

Blocking the hob operation

This function mode is intended as a protection against

accidental start or change of heating power by children or

house pets. The hob may be blocked by pressing the relevant

sensor for about 3 seconds, illuminating the LED signal lamp

above the sensor. The hob may be blocked both with the hob

switched on or off. The functioning of the complete hob is

blocked, except for the main hob switch and the blocking

sensor. In the blocked mode all hotplates may be switched off

only by pressing the main ON/OFF hob sensor, while the

blocked mode remains active. To activate a particular sensor in

the blocked mode, the signal lamp goes on for a few seconds.

If a particular hotplate is in timer automatic mode, the

countdown proceeds normally and the hotplate is switched off

at the expiry of preset time, signaling the end by the triple

beep.

The blocked mode may be switched off at anytime by pressing

the sensor. Short beep confirms the action, and the LED signal

lamp goes off.

Remaining heat display

Immediately after a particular hotplate is switched off, or in

case the complete hob is switched off, the indicator shows the

letter "H" as a warning that the "hotplate is hot". If the hob is

on and the power regulations are set at "0", the indicators

intermittently flash "0" and "H", while if the hob is switched off

the indicator displays only the warning letter "H".

When the warning signal is on do not touch the hotplate or

place any temperature sensitive objects on the relevant

hotplate. Danger of burns!

When the indicator goes off, the hotplate surface is cool

enough to be touched safely.

In case of mains interruption, the warning signal »H« is off

even in case the hotplate is actually still hot, so extra caution is

recommended.

Timer function

Timer function is activated by pressing either the (-) or the (+)

sensor. Time may be set between 1 and 99 minutes, and may

be altered by pressing either of the above sensors anytime.

This function offers two timer operation alternatives:

Gorenje ec 7969 e w b Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info