336340
16
Zoom out
Zoom in
Vorherige Seite
1/19
Nächste Seite
134422
Connections may be carried out by a quali ed technician
only. The earthing protection must comply with the standing
regulations.
Connection terminals are revealed when the connection box
cover is removed.
Prior any attempted connection check that the voltage
indicated on the rating plate is in line with your home power
supply.
The rating plate is located underneath the appliance.
The appliance is manufactured for use with the power supply
voltage 2N AC 400V.
The electric wiring should be equipped with a circuit breaker
able to isolate the appliance from the mains in all points,
with the distance between terminals of at least 3 mm in
open position. This may be done by means of fuses, safety
switches, etc.
The connection should be selected in accordance with the
declared charge capacity of the mains and the fuse power.
Such appliances are allowed to be mounted on one side next
to a high kitchen cabinet, the height of which may exceed that
of the appliance. On the opposite side however, only a kitchen
cabinet of equal height as the appliance is allowed.
Upon the completion of installation, live wires and isolated
cables must be adequately protected against accidental
touching.
ATTENTION !
Before attempting any repairs on the appliance, disconnect
the power supply. In accordance with the mains voltage the
appliance should be connected in line with the attached
diagram. The earthing wire (PE) must be connected to the
terminal marked with the earthing symbol
.
The connection cable must lead through the relief safety
device, protecting it from accidental pulling out. Upon the
completion of installation switch all the hotplates on for about 3
minutes to check the proper functioning.
Improper connection may damage parts of the appliance.
Such damages are not covered by warranty!
Before attempting any connections check whether voltage
indicated on the rating plate agrees with the installation in your
home. Authorized person must check the user connection
voltage (230 V against N) with the voltage meter!
Place the power lead at the rear of the appliance in such way
to avoid touching the rear panel of the appliance as it may
become hot during the operation.
Installation diagramInstallation diagram
37
Connection to the power supply
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gorenje ect 2700 p2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info