Bedienungsanleitung Gorenje gcs 64 c (Seite 4 von 9) (Englisch)

335443

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Instructions for Use, Building- in and Connecting

x

Be very precise when placing the burner crown

cap upon the crown. Always keep the crown

nozzles clean and free.

crown cap

burner crown

ceratin models only

thermal coupling

(certain models only)

correct position of

burner components

Ignition and operation of burners

Gas burners may be ignited with the electric

ignition device, built-in adjacent to each burner

(specific models only).

Single handed ignition

(specific models only)

To ignite the gas burner, press the selected

burner knob and turn it to the maximum power

position. The electric spark from the ignition

device flashes and sets fire to the escaping gas.

In case the electric ignition device may fail

due to power failure or moisture upon the

ignition spark, you may ignite the gas burner

with a simple match or a cigarette lighter.

Ignition of gas using both hands

(specific models only)

To ignite the gas burner, press the selected

burner knob and turn it to the maximum power

position. Now press the ignition device knob

several times. The electric spark from the ignition

device flashes and sets fire to the escaping gas.

In case the electric ignition device may fail

due to power failure or moisture upon the

ignition spark, you may ignite the gas burner

with a simple match or a cigarette lighter.

x Once the gas starts burning, keep the control

button pressed for about 10 seconds, until the

flame becomes constant.

x Release the button and set the desired power,

between the highest and the lowest position.

x Setting between the zero dot

and the

largest flame symbol is not recommended,

since the flame is not stable in that range, and

may easily get extinct.

x In case the flame goes out repeat the

procedure.

In case the burner fails to ignite

after 15 seconds, shut the gas to the burner off

and wait at least one minute before you attempt

to repeat the firing procedure.

x

If the burner flame is extinguished – for no

matter what reason – shut the gas to the burner

off and wait at least one minute before you

attempt to repeat the firing procedure.

x

Burner is switched off by turning the control

button to the right in the zero position

(black

dot).

gas faucet is closed

maximum power

minimum power

To ensure safe use of small

diameter dishes, place the

supplied extra wire grid upon

the auxiliary burner if

necessary.

Cookware

Selection of the adequate dish size ensures

optimized cooking time and consumption of gas.

Diameter of the dish is of utmost importance.

The flame reaching over the edge of the small

diameter dish may destroy the dish, while the

consumption of gas is increased.

Gas needs oxigen for burning. In case of

excessively large dish diameter the oxigen

supply is insufficient, consequently reducing the

burning capacity.

The wire grid (certain models only)

The wire grid is used for dishes with small

diameter. Place the grid over the auxiliary burner

crown.

Burner type Dish diameter

Large (3kW)

220-260 mm

Normal (1,75 kW)

180-220 mm

Auxiliary (1 kW)

120-180 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje gcs 64 c Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info