Bedienungsanleitung Gossen Metrawatt METRISO 1000A (Seite 6 von 10) (Englisch)

590651

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

6 GMC-I Messtechnik GmbH

5.2 Evaluation of Measurement Values

In order to assure that insulation resistance values do not fall below those

required by DIN VDE regulations, insulation tester inherent deviation must

be taken into consideration.

Required minimum display values for insulation resistance which take

maximum operational measurement deviation of the METRISO 1000A into

consideration (under nominal conditions of use) can be determined with

the following table. These are the minimum values which must be dis-

played, in order to assure that actual values do not fall below the required

limit values (DIN VDE 0413 part 1). Intermediate values can be interpo-

lated.

The table applies to a nominal voltage of 500 V. The values in the table must be

multiplied by a conversion factor for other nominal voltages.

5.3 Rapid Testing of Insulation Resistance

In addition to illuminating the measuring point, the lamp in the test probe

can also be used for rapid GO/NO-GO testing of insulation resistance. As

long as the lamp is lit, minimum values for insulation resistance are fulfilled

in accordance with DIN VDE 0100. The signal remains lit as long as

insulation resistance demonstrates the following values:

6 Measuring Low-Impedance Resistance (0 to 4 Ω)

Attention!

Make certain that the device under test is voltage-free before

performing measurements in the low-impedance measuring

range.

The measurement key should not be depressed if a high-

impedance device under test is probed, or if the test probes are

idle.

➭ Set the function selector switch to the “4 Ω” position.

➭ Briefly short circuit the test probes and press the measurement key to

check for full-scale deflection at “0 Ω”. The needle must point to the

“0” mark at the 4 Ω scale in the idle state. Readjust the needle if

necessary with the adjusting screw for mechanical zero adjustment.

➭ Probe the two points between which low-impedance resistance is to

be measured with the test probes.

➭ Activate the measurement key and read the measurement value from

the 4 Ω scale.

Notes:

• Resistance is measured with direct current.

If it can be expected that the measurement value will be influenced by

the polarity of the measuring current (e.g. if a diode is included in the

measuring circuit), reverse the test probes and repeat the

measurement.

• Resistance values which fluctuate at the beginning of the

measurement include, for example:

– Resistance with a high inductive component

– Incandescent lamp resistance values which change due to

warming caused by the measuring current

– Poor contact resistance at contact points

Scale R1 Scale R2 Scale R3

Limit Value

[MΩ]

Display Value

[MΩ]

Limit Value

[MΩ]

Display Value

[MΩ]

Limit Value

[MΩ]

Display Value

[MΩ]

0.1 0.13 0.2 0.25 2 2.5

0.2 0.25 0.3 0.38 3 3.8

0.3 0.38 0.4 0.5 4 5.0

0.5 0.63 5 6.3

11.251012.5

Insulation

Resistance

> 0.1 MΩ > 0.2 MΩ > 0.5 MΩ > 1 MΩ > 2 MΩ

Nominal

Voltage

50 V 100 V 250 V 500 V 1000 V

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRISO 1000A Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info